Garmin TR-1 manual To start Compass calibration, Step D. Release Select Load button

Page 31
Step B. [STBY] LED will blink for 30 seconds.

Sea Trial Setup: Steps 10-15 will need to be performed on open water, free of obstacles.

10.Calibrate your compass. The autopilot compass is made with a fluxgate. Like all compass installations, fluxgate installations are susceptible to local magnetic disturbances that will cause erroneous heading outputs. The autopilot computer can detect and correct deviations caused by magnets and iron materials around the fluxgate- if the earths’ magnetic field near the compass isn’t too distorted. Even though the compass corrects iron induced errors, don’t expect the correction to solve all ills associated with iron near the compass, placement of the compass in an iron free area is critical. You should only calibrate the compass on calm water. Stay away from large steel structures. Calibration will not work right if you try to do calibration with your boat on the trailer because the trailer is made with iron. Find some smooth water where you can drive in circles without running into anything.

1. Turn System On. Autopilot will be in Standby [STBY Mode] Step A. Press

and Release Deckmount Switch to turn autopilot on. Deckmount will begin to flash

Step C. When the Autopilot is done loading the [STBY] LED will light solid.

2. Press, release and light up the [Setup] LED on the Handheld, and enter code 47 on the handheld.

Step A. Press and release

Step B. Press and release

[Setup] button once to

[Left Chevron] button

illuminate [SETUP] LED.

once to illuminate the #4

 

LED.

Step C. Press and re- lease [Right Chevron] button once to illumi- nate the #7 LED.

3. To start Compass calibration.

Step A. Start driving the boat in a straight line.

Step D. Release [Select

Load] button

Step G. When the up arrow starts blinking, begin turning the boat to starboard.

Step B. Press and

HOLD the

[Select Load]

GPS button.

Step E. The [UP] arrow LED will light solid. (Continue driv- ing in a straight line.)

Step C. While holding down the [Select Load] button. Press and Release the [Deckmount] button once quickly.

Step F. Continue to drive in a straight line and watch for the [UP ARROW] LED to start blinking.

Step H. Turn at a rate that makes a full 360 degree turn in about 30 seconds. You will need to make at least 3 or more full turns. Keep turning until the [UP ARROW] & [DOWN ARROW] LED’s both light up. They will stay lit for about 5 seconds and the system will completely power down. Your compass is now calibrated.

If Up and Down Arrows both blink continuously, compass calibration has failed - you must turn the system off by holding the Deckmount On/Off button down in order to try calibration again. Make sure the compass is mounted at least 24” away from any magnetic material, i.e. radios, speakers etc. Make sure it is orientated in the bracket correctly.

31

Image 31
Contents TR-1 Autopilots Safety Contents 120-2525-00 120-2510-00 TR-1 Gladiator 1.2 or 2.0 Pump and ECU Parts ListHydraulic Layout for SeaStar Power Assisted Helms SeaStar Power AssistHydraulic Layout Single Helm Single Helm Boats OnlyHydraulic Layout Dual Helm Dual Helm Boats OnlyElectrical Layout Section II Setup Gladiator Installation & SetupSection IV Setup Codes Battery Connections. See Installation Overview and Check ListPreparation For Installation TR-1 Gladiator SpecificationsUnbalanced Kit These are examples of cylinders that Need an unbalanced kitProtection Unbalanced Valve adjustment and calibration Installation of Unbalanced ValveThese are examples of cylinders that Unbalanced Kit Pump Head Up Horizontally Installation Of Pump UnitExample Step two Placing ball in bracket Installation of Compass BallStep Three Adjusting Compass Ball Verify All Connections Prior to Applying power Installation Of Electronic Control Unit ECUNmea 0183 Connections Non-Compliant Nmea 0183 Devices Electrical Connections Installation Of Shadow Drive Valve Single Helm StationPump Motor Installation Of Shadow Drive Valve Dual Helm StationCompass Ball Horn Red + Orange + Installation Of Warning HornInstallation of On/Off Switch Using Waterproof Bezel Installation of Deckmount On/Off SwitchCorded Mount Flush Mount Installation Of HandheldPart Numbers 120-2045-04 ’s Gasoline Tachometry ConnectionsEvinrude E-Tech Bleeding Hydraulics Battery ConnectionsDockside Setup and Sea Trial Setup of Autopilot Step D. Release Select Load button To start Compass calibrationChevron button two times, and light up #5 LED With The GPS Connected to Autopilot Set NorthFine Tuning. Optional Trouble Shooting Guide How to Change Parameters of Setup Codes Description Code Values of the Parameters Factory Defaults Table of Setup Codes and Values of the ParametersDescription Code Table of Setup Codes and ParametersTachometer Codes Garmin GPS Connection GuideModel From GPS To Autopilot Nmea Out Manufacturer FurunoLowrance HummingbirdNorthStar MagellanRayMarine Simrad From GPS To Autopilot Nmea Out ManufacturerChapter Installation of Wireless RemoteParts List Wireless Two Button Description Qty Qty Parts List Wireless Five Button DescriptionThank You IntroductionKeypad push-button functions Wireless Remote Functions, Two ButtonKeypad push-button functions Wireless Remote Functions, Five ButtonWireless Installation Installation ConsiderationsAntenna Installation Security Codes Replacement Remote KeypadsChanging Batteries Limited Warranty 906-2520-00 Version H 110107
Related manuals
Manual 13 pages 3.61 Kb Manual 48 pages 48.1 Kb