Garmin TR-1 manual Set North, With The GPS Connected to Autopilot

Page 33

Set North

14.Set North. This needs to be done if any GPS or radar overlay functions are going to be used.

To run a GPS course requires that the autopilot compass is in agreement with the GPS’s magnetic map. You need to set North with the pilot in standby mode. Setting North may require a significant amount of clear sea space in front of your boat (at least 1/2 to 3/4 of a mile).

Verify that the NMEA connections for the GPS are functioning. Turn on the GPS. With the Autopilot in [Standby], press and release

[Setup] button on the handheld. Press and light up the number 4 and the number 8 LED’s [Code 48]. If the [up arrow] LED lights when you hold down the [Select Load] (GPS) button, the autopilot does not acknowledge the validity of the GPS data.

With The GPS Connected to Autopilot:

Step A. With the system in [STBY]

Step B. Press and release [Setup]

 

button once to illuminate (left) LED

Step C. Press and release [left chev- ron] button one time to illuminate the #4 LED.

(You have now selected code 48)

Step D. Press and release the [Right Chevron] button TWO times to illuminate the #8 LED.

Step E. Run your boat at planing speed at a constant heading. You will need at least 1/2 mile of haz- ard free water in front of you.

Step F. Press and HOLD the GPS [Select Load] button. The Load LED will illuminate.

Step G. While holding down the [Select Load] button. Press and Release the [Deckmount] button quickly.

Step H. Release the [Select Load] button, after [Load] LED diminishes. The system will power down after North is set.

33

Image 33
Contents TR-1 Autopilots Safety Contents 120-2525-00 120-2510-00 TR-1 Gladiator 1.2 or 2.0 Pump and ECU Parts ListHydraulic Layout for SeaStar Power Assisted Helms SeaStar Power AssistHydraulic Layout Single Helm Single Helm Boats OnlyHydraulic Layout Dual Helm Dual Helm Boats OnlyElectrical Layout Gladiator Installation & Setup Section II SetupSection IV Setup Codes Battery Connections. See Installation Overview and Check ListPreparation For Installation TR-1 Gladiator SpecificationsUnbalanced Kit These are examples of cylinders that Need an unbalanced kitProtection Installation of Unbalanced Valve Unbalanced Valve adjustment and calibrationThese are examples of cylinders that Unbalanced Kit Pump Head Up Horizontally Installation Of Pump UnitExample Step two Placing ball in bracket Installation of Compass BallStep Three Adjusting Compass Ball Verify All Connections Prior to Applying power Installation Of Electronic Control Unit ECUNmea 0183 Connections Non-Compliant Nmea 0183 Devices Electrical Connections Installation Of Shadow Drive Valve Single Helm StationPump Motor Installation Of Shadow Drive Valve Dual Helm StationCompass Ball Horn Red + Orange + Installation Of Warning HornInstallation of On/Off Switch Using Waterproof Bezel Installation of Deckmount On/Off SwitchInstallation Of Handheld Corded Mount Flush MountPart Numbers 120-2045-04 ’s Gasoline Tachometry ConnectionsEvinrude E-Tech Bleeding Hydraulics Battery ConnectionsDockside Setup and Sea Trial Setup of Autopilot Step D. Release Select Load button To start Compass calibrationChevron button two times, and light up #5 LED With The GPS Connected to Autopilot Set NorthFine Tuning. Optional Trouble Shooting Guide How to Change Parameters of Setup Codes Description Code Values of the Parameters Factory Defaults Table of Setup Codes and Values of the ParametersDescription Code Table of Setup Codes and ParametersTachometer Codes Model From GPS To Autopilot Nmea Out Manufacturer GPS Connection GuideFuruno GarminLowrance HummingbirdMagellan NorthStarRayMarine Simrad From GPS To Autopilot Nmea Out ManufacturerChapter Installation of Wireless RemoteParts List Wireless Two Button Description Qty Qty Parts List Wireless Five Button DescriptionThank You IntroductionKeypad push-button functions Wireless Remote Functions, Two ButtonKeypad push-button functions Wireless Remote Functions, Five ButtonInstallation Considerations Wireless InstallationAntenna Installation Replacement Remote Keypads Security CodesChanging Batteries Limited Warranty 906-2520-00 Version H 110107
Related manuals
Manual 13 pages 3.61 Kb Manual 48 pages 48.1 Kb