Garmin TR-1 manual Tachometer Codes

Page 35

Table of Setup Codes and Parameters

 

TACHOMETER CODES

 

 

 

 

 

Description

Code

Values of the Parameters

Factory

 

 

 

Defaults

RPM Source Configuration

259 1, none/ 2, Port/ 3, Starboard/ 4, Both

2

Code 259: For single engine installations, set this code to 2 (1 blink) (and hook the blue and black wires up to your engine tach leads).

Pulses per Revolution

267

1 to 255 by 1’s

6

Code 267: The number of tach pulses per engine revolution is an engine specific parameter. The following settings are a good starting point, however you need to verify them on operation. V8 engines 4 ppr (3 blinks) Most outboards 6 ppr

Show Port RPM

35

Hold Down [Select Load] button: 1000’s blink on

 

 

 

Up Arrow 100’s blink on Down Arrow

 

Show Starboard RPM

36

Same As Above

 

Transition RPM

348

100 to 6000 by 100’s

3000

Code 348: Set this code to the RPM’s that your boat runs when almost on plane.

Low RPM Limit

357

100 to 6000 by 100’s

500

Code 357: If your autopilot runs well at all RPMs but is a little too active at idle, you can increase this low limit RPM to a setting that is higher than your idle RPM to reduce autopilot rudder activity at idle.

High RPM Limit

359

100 to 6000 by 100’s

6000

Code 359: If your autopilot runs well at all RPM’s but you would like a little stiffer heading hold at the top end, reducing this setting to an RPM lower than your actual peak RPM will help

 

 

HYDRAULIC CODES

 

 

 

 

 

Description

Code

Values of the Parameters

Factory

 

 

 

Defaults

Helm Displacement

269

.1 to 6 by .1’s

1.7

 

 

 

 

Pump Displacement

169

[Up Arrow] for 4 liter, [Down Arrow] for 2 liter

2 liter

 

 

 

 

Turns Lock to Lock

26

.1 to 10 by .1’s

4.5

 

 

 

 

Sloppy Linkage Compensation

257

8 settings, 8 for most sloppy

1

Code 257: In case of sloppy and loose steering linkages, increasing this parameter may help to reduce heading oscillations due to the linkage. Use with caution.

Shadow Drive Desensitize

368 1 most sensitive, 40 least sensitive

20

Code 368: If the shadow drive is being false tripped, i.e., autopilot is disconnected when the helm is held still, increasing this parameter may help. False tripping is usually due to leakage of fluid past the helm pump lock valve. You may need to repair the helm valves if you cannot eliminate false trips.

Shadow Drive Enable

367

[Up Arrow] for On, [Down Arrow] for Off

on

 

 

 

 

Reversed Hoses

249

[Up Arrow] for Reversed, [Down Arrow] for Normal

Norm

Code 249: In case of hoses installed backwards, use this code to electronically reverse the steering direction.

35

Image 35
Contents Safety Contents Compass Ball TR-1 Gladiator 2.1 Liter System Parts ListEa. #14 x 1 Phillips Pan Head screw 310-0072-18 Pump Unit Electronic Control UnitAccessory Pack TR-1 Gladiator System Parts ListSingle Helm Hydraulic Layout Dual Helm Hydraulic Layout Electrical Layout Section IV Setup Codes Gladiator Installation & SetupSection II Setup Battery Connections. See Installation Check ListPreparation For Installation TR-1 Gladiator SpecificationsProtection Magnetic Environment Installation Of Pump Unit Keep Separated Installation Of Electronic Control Unit ECUVerify All Connections Prior to Applying power Step Four Connection Installation of Compass BallNmea 0183 Connections Non-Compliant Nmea 0183 Devices Electrical Connections Installation Of Shadow Drive Valve Single Helm StationInstallation Of Shadow Drive Valve Dual Helm Station Compass Ball Horn Red + Orange + Installation Of Warning HornInstallation of On/Off Switch Using Standard Bezel Installation of Deckmount On/Off SwitchInstallation of On/Off Switch Using Waterproof Bezel Flush Mount Installation Of HandheldCorded Mount Corded Mount’s Gasoline Tachometry ConnectionsEvinrude E-Tech Bleeding Hydraulics Battery ConnectionsSection Dockside Setup and Sea Trial Setup of AutopilotStep D. Release Select Load button To start Compass calibrationChevron button two times, and light up #5 LED With The GPS Connected to Autopilot Set NorthFine Tuning. Optional Trouble Shooting Guide How to Change Parameters of Setup Codes Description Code Values of the Parameters Factory Defaults Table of Setup Codes and Values of the ParametersDescription Code Table of Setup Codes and ParametersTachometer Codes Garmin GPS Connection GuideModel From GPS To Autopilot Nmea Out Manufacturer FurunoLowrance HummingbirdRayMarine From GPS To Autopilot Nmea Out ManufacturerMagellan NorthStarSimrad Section Installation of Wireless RemoteSection I Parts List Section III InstallationParts List Wireless Two Button Description Qty Qty Parts List Wireless Five Button DescriptionThank You SafetyIntroduction Keypad push-button functions Wireless Remote Functions, Two ButtonKeypad push-button functions Wireless Remote Functions, Five ButtonAntenna Installation Installation ConsiderationsWireless Installation Changing Batteries Replacement Remote KeypadsSecurity Codes Limited Warranty
Related manuals
Manual 13 pages 3.61 Kb Manual 53 pages 31.36 Kb