Icom IC-F5061, IC-F5063, IC-F5062 Adjustment Procedures, Preparation, Starting Software Adjustment

SECTION 6 ADJUSTMENT PROCEDURES

6-1 PREPARATION

When adjusting IC-F5060 series transceiver, CS-F5060 CLONING SOFTWARE, CS-F5060 ADJ ADJUSTMENT SOFTWARE (Rev. 1.0 or lat- er), RS-232C cable, JIG cable (modified OPC-1122/U CLONING CABLE; see the page 6-2) and the following test equipments are required.

EQUIPMENT	GRADE AND RANGE		EQUIPMENT	GRADE AND RANGE
DC power supply	Output voltage	: 13.6 V DC [USA]		Power attenuation	: 50 or 60 dB
		13.2 V DC [EUR], [EXP]	Attenuator	Capacity	: 60 W [USA]
	Current capacity	: More than 1.5 A			30 W [EUR], [EXP]
modulation analyzer	Frequency range	: DC–300 MHz	External speaker	Input impedance	: 4 Ω
	Measuring range	: 0 to ±10 kHz		Capacity	: 5 W or more
	Frequency range	: 0.1–300 MHz	Standard signal	Frequency range	: 0.1–300 MHz
Frequency counter	Frequency accuracy	: ±1 ppm or better			: 0.1 µV to 32 mV
			generator (SSG)	Output level
	Sensitivity	: 100 mV or better			(–127 to –17 dBm)
	Measuring range	: 0.1–60 W [USA]	Oscilloscope	Frequency rang	: DC–20 MHz
		0.1–30 W [EUR], [EXP]		Measuring range	: 0.01–20 V
RF power meter	Frequency range	: 100–300 MHz
				Input impedance	: 50 kΩ
	Impedance	: 50 Ω	Digital voltmeter
	SWR	: Better than 1.2 : 1		Measuring range	: 0.1–10V

▄SYSTEM REQUIREMENTS (for the ADJUSTMENT SOFTWARE)

• Microsoft® Windows® 98/98SE/Me/2000/XP • RS-232C serial port (D-sub 9 pin)

▄ADJUSTMENT SOFTWARE INSTALLATION q Quit all applications when Windows is running. w Insert the CD into the appropriate CD drive.

e Double-click the “Setup.exe” contained in the ‘CS-F5060 ADJ’ folder in the CD drive.

r The “Welcome to the InstallShield Wizard for CS-F5060 ADJ” will appear. Click [Next>].

t The “Choose Destination Location” will appear. Then click [Next>] to install the software to the destination folder. (e.g. C:\Program Files\Icom\CS-F5060 ADJ)

y After the installation is completed, the “InstallShield Wiz- ard Complete” will appear. Then click [Finish].

u Eject the CD.

i Program group ‘CS-F5060 ADJ’ appears in the ‘Programs’ folder of the start menu, and ‘CS-F5060 ADJ’ icon ap- pears on the desk top screen.

▄STARTING SOFTWARE ADJUSTMENT

q Connect the transceiver and PC with RS-232C cable and

JIG CABLE.

w Turn the transceiver power ON.

e Boot up Windows, and click the program group ‘CS-F5060 ADJ’ in the ‘Programs’ folder of the [Start] menu, then CS-F5060 ADJ’s window appears.

r Click ‘Connect’ on the CS-F5060 ADJ’s window, then the window shows transceiver’s condition and adjustment items as below.

t Set or modify adjustment data as specifi ed.

Microsoft and Windows are registered trademarks of Micro- soft Corporation in the U.S.A. and other countries.

▄BEFORE STARTING SOFTWARE ADJUSTMENT

Clone the adjustment frequencies and settings into the transceiver, and set the confi guration using the CS-F5060 CLONING SOFT- WARE before starting the software adjustment. Otherwise, the software adjustment can not be started.

CAUTION!: BACK UP the originally programmed memory data in the transceiver before programming the adjustment frequencies. When program the adjustment frequencies into the transceiver, the transceiver’s memory data will be overwritten and lose original memory data at the same time.

• ADJUSTMENT FREQUENCY LIST

CH	FREQUENCY		SETTING	CH	FREQUENCY		SETTING
1	154.900 MHz	• TX power	: Low1	10	174.000 MHz	• TX power	: Low1
		• Mode	: Narrow			• Mode	: Narrow
2	174.000 MHz	• TX power	: Low1	11*	155.000 MHz	• TX power	: Low1
		• Mode	: Wide			• Mode	: Middle
3	136.000 MHz	• TX power	: Low1	12*	136.000 MHz	• TX power	: High
		• Mode	: Wide			• Mode	: Middle
4	155.000 MHz	• TX power	: Low1	13*	174.000 MHz	• TX power	: Low2
		• Mode	: Wide			• Mode	: Middle
5	136.000 MHz	• TX power	: High	14	155.000 MHz	• TX power	: Low1
		• Mode	: Narrow			• Mode	: Digital
6	136.000 MHz	• TX power	: Low2	15	136.000 MHz	• TX power	: Low1
		• Mode	: Wide			• Mode	: Digital
		• TX power	: Low1			• TX power	: Low1
7	155.000 MHz	• Mode	: Middle	16	174.000 MHz
						• Mode	: Digital
		• DTCS	: 007
8	155.000 MHz	• TX power	: Low1	17	136.000 MHz	• TX power	: Low1
		• Mode	: Narrow			• CTCSS	: 151.4 Hz
		• TX power	: Low1			• TX power	: Low1
9	136.000 MHz			18	136.000 MHz	• Mode	: Wide
		• Mode	: Narrow
						• DTMF	: P3

*; [EUR] only

6 - 1