3M 11000 operating instructions Specifications

Page 21

4-SPECIFICATIONS

4.1Power Requirements 115V, 60 Hz, 2.8 Amp

5.2bar gauge pressure [75 PSIG], 28 litre/min @ 21°C, 1.01 bar [1.0 SCFM] at random cycle rate.

4.2Operating Rate:

Belt speed is 0.37m/s [72 F.P.M.]

Actual production rate is dependent on operator's dexterity. Boxes must be 18 inches (457mm) apart minimum.

4.3Operating Conditions

Use in dry, relatively clean environments at 4.4 C to 48.9o C [40o F to 120o F] with clean, dry boxes.

Note: Machine should not be washed or subjected to conditions causing moisture condensation on components.

WARNING

•To reduce the risk associated with ﬁre and explosion hazards:

−Do not operate this equipment in potentially ﬂammable or explosive environments.

4.4Box Board

125 to 275 P.S.I. bursting test, single wall B, or C ﬂute.

4.5Box Weight and Size Capacities

A.Box weight, ﬁlled – weight must be sufﬁcient to actuate center cam located between powered conveyor rollers, 2 kg [4 lbs] minimum, 29 kg [65 lbs] maximum.

B . Box Size:	Minimum		Maximum
Length	150mm [6.0 inch]		635mm [25 inch]
Width	120mm	[4.75 inch]	495mm	[19.50 inch]
Height	120mm	[4 .75 inch]	510mm	[20 inch]

Special modiﬁcations may be available for carton sizes not listed above.

Contact your 3M Representative for information.

a80f-if-NA

13

2011 June

Image 21

Contents 3M 2011 44-0009-2097-3 B060311-NA 3M Industrial Adhesives and TapesPage Industrial Adhesives and Tapes Replacement Parts and Service Information To Our CustomersThis page is Blank Safety Table of Contents A80f-if Infeed ConveyorIntroduction General InformationThis page is Blank Installation and Operation Table of Contents UnpackingMaintenance Additional InstructionsPLC Abbreviations and Acronyms List of ABBREVIATIONS, AcronymsIntroduction Manufacturing Speciﬁcations / Description / Intended Use3M-MaticTMa80f-if Infeed Conveyor, Type How to Update the Manual in Case Introduction Manual MaintenanceConsulting the Manual Publication 3M 2011Data Identifying Manufacturer and Machine General InformationContents a80f-if Infeed Conveyor Safety General Safety InformationStop Machine while the machine is running To reduce the risk associated with pinch hazards To reduce the risk associated with muscle strainOperators Qualiﬁcations Personal Safety MeasuresNumber of Operators Residual HazardsEmergency Stop Skill 1 Machine OperatorA80f-if Infeed Conveyor Components Component Locations78-8068-3859-1 Leg Label 78-8060-8481-6 3M Logo not shown 78-8070-1339-2 Label ServiceThis page is Blank Specifications Min Machine Dimensions Minimum Specifications Max MinSHIPMENT-HANDLING-STORAGE, Transport Handling and Transportation of Uncrated MachineStorage of the Packed or Unpacked Machine Unpacking Installation and Operation Pneumatic Connection Preliminary Electric InspectionFront and Rear Flaps See -SpeciﬁcationsProduction Line Placement of Infeed Conveyor Installation and Operation Pneumatic ConnectionMuscle strain Impact hazardsTimer Installation and Operation Box Release TimerStop Gate Pneumatic Components FunctionSide Guide Setup Side Guides Maintenance and Repairs Safety Measures See sectionTools and Spare Parts Supplied with the Machine Lubrication Products Lubrication Qualiﬁcation / SkillA80f-if-NA June Case of Fire Additional Instructions Enclosures / Special InformationA80F-IF Technical Diagrams Electric Diagram Label Kit Tool KitPart Number Option/Accessory Options and AccessoriesThis page is Blank FigureFig.1541415414 FigureFig.1541615416A80f-if-NA June A80F-IFA80f-if Ref. No 3M Part No Description Ottobre A80f-if Ref. No 3M Part No Description 19 1818 A80f-if Ref. No 3M Part No Description Ottobre A80f-if Ref. No 3M Part No Description 1717 A80f-if Ref. No 3M Part No Description A80F-IF A80f-if Adjustable Case SealerA80f-if Ref. No 3M Part No Description Page A80f-if Ref. No 3M Part No Description This page is Blank