7-INSTALLATION AND OPERATION (continued)
Box Release Timer: |
|
|
|
|
|
|
|
| ||
The Box Release Timer, shown in Figure |
| Figure | ||||||||
located below the conveyor bed at the infeed end of |
| |||||||||
|
|
|
|
|
|
|
| |||
the conveyor. The timer controls the box stop gate |
|
|
|
|
|
|
|
| ||
that releases the boxes to the |
|
|
|
|
|
|
|
| ||
The timer is adjustable for box lengths from 15mm |
|
|
|
|
|
|
|
| ||
|
|
|
| Box Release | ||||||
[6 inch] to 635mm [25 inch]. The timer must be |
|
|
|
| Timer |
|
| |||
reset for each change in box length being conveyed |
|
|
|
|
|
|
|
| ||
through the a80if case sealer. |
|
|
|
|
|
|
|
| ||
For compressed air supply Technical Specifications, |
|
|
|
|
|
|
|
| ||
Note: A precision regulator is used to balance |
|
|
|
|
|
|
|
| ||
the top drive assembly. Due to the self- |
|
|
|
|
|
|
|
| ||
relieving feature of this regulator, a small |
|
|
|
|
|
|
|
| ||
amount of air continually vents to the |
|
|
|
|
|
|
|
| ||
atmosphere. This is normal and amounts |
|
|
|
|
|
|
|
| ||
to approximately 3 litre/min. [0.1 SCFM]. |
|
|
|
|
|
|
|
| ||
|
| WARNING |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• To reduce the risk associated with |
|
|
|
|
|
|
|
| ||
entanglement and electric hazards: |
|
|
|
|
|
|
|
| ||
− Keep hands and loose clothing away from |
|
|
|
|
|
|
|
| ||
moving rollers |
|
|
|
|
|
|
|
| ||
− Remove tools and/or other loose objects |
|
|
|
|
|
|
|
| ||
before starting conveyor |
|
|
|
|
|
|
|
| ||
− Turn off and disconnect electrical and |
|
|
|
|
|
|
|
| ||
air supply power before performing any |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
maintenance or service work on the infeed |
|
|
|
|
|
|
|
| ||
conveyor |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
• To reduce the risk associated with |
| Figure | ||||||||
impact hazards: |
|
|
|
|
|
|
|
| ||
− Always turn the valve "Off" when air supply |
|
|
|
|
|
| ||||
|
| Stop | ||||||||
line is being connected or disconnected. |
|
| Gate |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
Pneumatic Components Function |
|
|
|
|
|
|
|
| ||
The air supply operates the adjustable pneumatic |
|
|
|
|
|
|
|
| ||
timer and powers movement of two air cylinders that |
|
|
|
|
|
|
|
| ||
raise the |
|
|
|
|
|
|
|
| ||
box for the tape sealing application. The box cam |
|
|
|
|
|
|
|
| ||
activates the same two air cylinders that lower the |
|
|
|
|
|
|
|
| ||
box rollers and the stop gate retains the next box |
|
|
|
|
|
|
|
| ||
from moving forward. |
|
|
|
|
|
|
|
| ||
Electrical Components Function |
|
|
|
|
|
|
|
| ||
A motor, reducer and drive chain turn the powered |
|
|
|
|
|
|
|
| ||
box rollers that convey the box forward for the tape |
|
|
|
|
|
|
|
| ||
sealing application. |
|
|
|
|
|
|
|
| ||
Operating Sequence |
|
|
|
|
|
|
|
| ||
1. The operator places one product filled box |
|
|
|
|
| Center Cam |
| |||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |||
(front and rear flaps folded in) onto the infeed |
|
|
|
|
|
|
|
| ||
conveyor |
|
|
|
|
|
|
|
| ||
position) and moves it forward to the stop gate |
|
|
|
|
|
|
|
| ||
as shown in Figure |
|
|
|
|
|
|
|
| ||
20 |
|
|
|
|
| 2011 June |