3M 11000 operating instructions Side Guide Setup Side Guides

Page 29

7-INSTALLATION AND OPERATION (continued)

2.The operator moves the side guides in against the box to center it on the conveyor rollers and tightens the four hand knobs to secure the side guides. See Figure 7-8.Box must be aligned with guides to match a80f-ifside drive belts.

Additional boxes, ready for the tape sealing application, are moved in to ﬂood the conveyor behind the lead box.

3.The operator rotates the electrical switch to "On" to start the powered box rollers.

4.The operator moves the lead box forward onto the powered box rollers. The box moves over the center cam that activates the timer causing the non-powered rollers to pivot down so the stop gate retains the following box.

5.The lead box moves through the case sealer taping application. The timer on the infeed conveyor has been set to raise the non-powered rollers releasing the next box.

Note – Roller drive motor is designed to run at a moderate temperature of 40° C [104° F]. In some cases, it may feel warm to the touch.

Figure 7-8 – Side Guide Setup

Side Guides

a80f-if-NA

21

2011 June

Image 29

Contents 3M 2011 44-0009-2097-3 B060311-NA 3M Industrial Adhesives and TapesPage Industrial Adhesives and Tapes Replacement Parts and Service Information To Our CustomersThis page is Blank Safety Table of Contents A80f-if Infeed ConveyorIntroduction General InformationThis page is Blank Installation and Operation Table of Contents UnpackingMaintenance Additional InstructionsPLC Abbreviations and Acronyms List of ABBREVIATIONS, Acronyms3M-MaticTMa80f-if Infeed Conveyor, Type IntroductionManufacturing Speciﬁcations / Description / Intended Use How to Update the Manual in Case Introduction Manual MaintenanceConsulting the Manual Publication 3M 2011Data Identifying Manufacturer and Machine General InformationContents a80f-if Infeed Conveyor Stop SafetyGeneral Safety Information Machine while the machine is running To reduce the risk associated with pinch hazards To reduce the risk associated with muscle strainOperators Qualiﬁcations Personal Safety MeasuresNumber of Operators Residual HazardsEmergency Stop Skill 1 Machine OperatorA80f-if Infeed Conveyor Components Component Locations78-8068-3859-1 Leg Label 78-8060-8481-6 3M Logo not shown 78-8070-1339-2 Label ServiceThis page is Blank Specifications Min Machine Dimensions Minimum Specifications Max MinStorage of the Packed or Unpacked Machine SHIPMENT-HANDLING-STORAGE, TransportHandling and Transportation of Uncrated Machine Unpacking Installation and Operation Pneumatic Connection Preliminary Electric InspectionFront and Rear Flaps See -SpeciﬁcationsProduction Line Placement of Infeed Conveyor Installation and Operation Pneumatic ConnectionMuscle strain Impact hazardsTimer Installation and Operation Box Release TimerStop Gate Pneumatic Components FunctionSide Guide Setup Side Guides Tools and Spare Parts Supplied with the Machine Maintenance and RepairsSafety Measures See section Lubrication Products Lubrication Qualiﬁcation / SkillA80f-if-NA June Case of Fire Additional Instructions Enclosures / Special InformationA80F-IF Technical Diagrams Electric Diagram Label Kit Tool KitPart Number Option/Accessory Options and AccessoriesThis page is Blank FigureFig.1541415414 FigureFig.1541615416A80f-if-NA June A80F-IFA80f-if Ref. No 3M Part No Description Ottobre A80f-if Ref. No 3M Part No Description 19 1818 A80f-if Ref. No 3M Part No Description Ottobre A80f-if Ref. No 3M Part No Description 1717 A80f-if Ref. No 3M Part No Description A80F-IF A80f-if Adjustable Case SealerA80f-if Ref. No 3M Part No Description Page A80f-if Ref. No 3M Part No Description This page is Blank