Eagle Electronics 500CDF manual Internal tooth washer TMB-S bracket Bolt Nut Flat washer

Page 25

If you need to drill a hole in the transom to pass the connector through, the required hole size will be 5/8".

Caution:

If you drill a hole in the transom for the cable, make sure it is lo- cated above the waterline. After installation, be sure to seal the hole with the same marine grade above- or below-waterline seal- ant used for the mounting screws.

7.Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the transducer bracket down. This puts the transducer deeper into the water, hope- fully below the turbulence causing the noise. Don't allow the transducer bracket to go below the bottom of the hull!

Trolling Motor Bracket Installation (single-frequency only)

1.Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer. (Note: The internal tooth washer is supplied with the TMB-S.)

Internal tooth washer

TMB-S bracket

Bolt

 

Nut

Flat washer

Attach motor mounting bracket to transducer.

2.Slide the adjustable strap supplied with the TMB-S through the slot in the transducer bracket and wrap it around the trolling motor. Posi- tion the transducer to aim straight down when the motor is in the wa- ter. Tighten the strap securely.

3.Route the transducer cable alongside the trolling motor shaft. Use plastic ties (not included) to attach the transducer cable to the trolling

19

Image 25
Contents Installation and Operation Instructions Page Table of Contents ColorLine level To turn Auto Sensitivity back on Page How this manual can get you out on the water, fast Read Me FirstPage Figuration and installation, bottom composi How Sonar Works How to Use this Manual Typographical Conventions Page Preparations Transducer InstallationSingle-frequency transom installations Pad Deadrise less than Strakes Good and poor transducer locations Transom Page Dot Alignment letters Positions Transducer Ratchets Bolt Transom Bottom Hull Flat-bottom hull Deep-vee hull Internal tooth washer TMB-S bracket Bolt Nut Flat washer Transducer mounted on trolling motor, side view Partial fish arches Hulls With Flotation Materials Transducer location High speed Trolling speed Page Epoxy transducer to hull Speed/Temperature Sensors Optional Speed Sensor Installation Good location Power Connections Power connections for the sonar unit Page Front 72.9 173.9 23.4 157.9 Millimeter 56.9 Inch In-Dash Template Face Cover Page Keyboard Basic Sonar OperationPower/lights on and off Main Menu Pages Pages Menu, showing Sonar display options Page Page Sonar Page, showing full sonar chart mode Basic Sonar Quick Reference Sonar Operations Page Page Important Tip Page Page Page ASP Advanced Signal Processing Sonar Options & Other FeaturesAlarms To adjust and turn on the shallow alarm To turn off the alarm, press ALARM↓ to Deep Alarm Enabledentexit Backlight Level Calibrate Speed Chart Speed ColorLine Thin or no ColorLine Wider ColorLine Depth Cursor ContrastDepth Range Manual Depth Range AutomaticFasTrack Fish I.D. Fish Symbols & Depths FishTrack Frequency Change Transducer Frequency SeaFinder CDF only Symbols with FishTrack depthsSonar Features menu with a frequency of 200 kHz selected Noise Rejection HyperScrollOverlay Data Page To return to the previous page, press Exit Tip Ping Speed & HyperScrollPage Pop-up Help Reset Options Screen Contrast and Backlight Level Reset Water DistanceSet Keel Offset Press MENUMENU↓ to SET Keel Offsetent Sensitivity & Auto Sensitivity Page Software Version Information Set LanguageSonar Page & Sonar Chart Display Options Sonar Chart ModePage Page Customizing the Digital Data/Chart Screen Sonar Simulator Stop Chart Surface Clarity Press ↓ or ↑ to select clarity levelEXITEXIT Units of Measure TransparencyZoom & Zoom Bar VolumeZoom Pan Troubleshooting Page Page Page Supplemental Material FCC Compliance Page Index Page Page 102 103 How to Obtain Service… Accessory Ordering Information for all countries Visit our web site