Eagle Electronics 500CDF manual

Page 18

Typically, shoot-thru-hull installations give excellent high speed opera- tion and good to excellent depth capability. There is no possibility of transducer damage from floating objects, as there is with a transom- mounted transducer. A transducer mounted inside the hull can't be knocked off when docking or loading on a trailer.

However, the shoot-thru-hull installation does have its drawbacks. First, some loss of sensitivity does occur, even on the best hulls. This varies from hull to hull, even from different installations on the same hull. This is caused by differences in hull lay-up and construction.

Second, the transducer angle cannot be adjusted for the best fish arches on your sonar display.

Lack of angle adjustment can be particularly troublesome on hulls that sit with the bow high when at rest or at slow trolling speeds.

Third, a transducer CAN NOT shoot through wood and metal hulls. Those hulls require either a transom mount or a thru-hull installation.

Fourth, if your Skimmer transducer has a built in temp sensor, it will only show the temperature of the bilge, not the water surface temp.

Follow the testing procedures listed in the shoot-thru-hull installation section at the end of this instruction booklet to determine if you can satisfactorily shoot through the hull.

Transom Transducer Assembly and Mounting

The best way to install these transducers is to loosely assemble all of the parts first, place the transducer's bracket against the transom and see if you can move the transducer so that it's parallel with the ground.

The following instructions sometimes vary depending on the mounting bracket that came with your transducer. Single frequency Skimmers come with a one-piece stainless steel bracket, while dual frequency Skimmers come with a two-piece plastic mounting bracket. Use the set of instructions that fits your model.

12

Image 18
Contents Installation and Operation Instructions Page Table of Contents ColorLine level To turn Auto Sensitivity back on Page Read Me First How this manual can get you out on the water, fastPage Figuration and installation, bottom composi How Sonar Works How to Use this Manual Typographical Conventions Page Transducer Installation PreparationsSingle-frequency transom installations Pad Deadrise less than Strakes Good and poor transducer locations Transom Page Dot Alignment letters Positions Transducer Ratchets Bolt Transom Bottom Hull Flat-bottom hull Deep-vee hull Internal tooth washer TMB-S bracket Bolt Nut Flat washer Transducer mounted on trolling motor, side view Partial fish arches Hulls With Flotation Materials Transducer location High speed Trolling speed Page Epoxy transducer to hull Speed/Temperature Sensors Optional Speed Sensor Installation Good location Power Connections Power connections for the sonar unit Page Front 72.9 173.9 23.4 157.9 Millimeter 56.9 Inch In-Dash Template Face Cover Page Basic Sonar Operation KeyboardPower/lights on and off Main Menu Pages Pages Menu, showing Sonar display options Page Page Sonar Page, showing full sonar chart mode Basic Sonar Quick Reference Sonar Operations Page Page Important Tip Page Page Page Sonar Options & Other Features ASP Advanced Signal ProcessingAlarms To adjust and turn on the shallow alarm To turn off the alarm, press ALARM↓ to Deep Alarm Enabledentexit Backlight Level Calibrate Speed Chart Speed ColorLine Thin or no ColorLine Wider ColorLine Contrast Depth CursorDepth Range Automatic Depth Range ManualFasTrack Fish I.D. Fish Symbols & Depths FishTrack Symbols with FishTrack depths Frequency Change Transducer Frequency SeaFinder CDF onlySonar Features menu with a frequency of 200 kHz selected HyperScroll Noise RejectionOverlay Data Page To return to the previous page, press Exit Ping Speed & HyperScroll TipPage Pop-up Help Reset Options Reset Water Distance Screen Contrast and Backlight LevelSet Keel Offset Press MENUMENU↓ to SET Keel Offsetent Sensitivity & Auto Sensitivity Page Set Language Software Version InformationSonar Chart Mode Sonar Page & Sonar Chart Display OptionsPage Page Customizing the Digital Data/Chart Screen Sonar Simulator Stop Chart Surface Clarity Press ↓ or ↑ to select clarity levelEXITEXIT Transparency Units of MeasureVolume Zoom & Zoom BarZoom Pan Troubleshooting Page Page Page Supplemental Material FCC Compliance Page Index Page Page 102 103 How to Obtain Service… Accessory Ordering Information for all countries Visit our web site