Furuno LS-6100 manual Choosing Picture Advance Speed, Adjusting the gain, Unit Basic Range

Page 14

Table 1-1 Default ranges

Unit

 

 

 

Basic Range

 

 

1

2

3

4

5

6

7

8

 

meters

5

10

20

40

80

150

200

300

feet

15

30

60

120

200

400

600

1000

fathoms

3

5

10

20

40

80

120

200

P/B

3

5

10

30

50

100

150

200

1.Press the [+] or [-] key of the [RANGE] key and the display should now look something like the one below.

2.Press the [+] or [-] key of the [RANGE] key again to choose a basic range.

1000ft

600ft

400ft

200ft

120ft

60ft

30ft

15ft

Basic ranges (default)

Shifting the range

The basic range may be shifted up or down in the manual mode as follows:

1.Press the [MENU/ESC] key to open the menu.

2.Choose SHIFT from page 1 of the menu.

3.Press ► to open the shift options window.

Adjusting the gain

The [GAIN] key adjusts the sensitivity of the receiver. Generally, use a higher gain setting for greater depths and a lower setting for shallower waters.

Gain too high Gain proper Gain too low

Examples of proper and improper gain

1.Press the [GAIN] key and the display shown below appears.

GAIN

Min Max

 

 

 

 

 

 

200k

 

 

 

2

 

 

 

 

 

 

50k

 

 

 

 

 

3

 

 

 

 

 

 

Gain adjustment window

2.When using the dual frequency display, press ▲ or ▼ to choose frequency.

3.Press the [GAIN] key to set. (You may also use ◄ or ►.) Adjust so that a slight amount of noise remains on the screen.

4.Press the [MENU/ESC] key to close the gain adjustment window.

0ft

Shift window

4.Use ▲ or ▼ to choose amount of shift desired.

5.Press the [MENU/ESC] key to close the menu.

Note: The picture may not be displayed if the amount of shift is greater than actual depth.

1.8Choosing Picture Advance Speed

The picture advance speed determines how quickly the vertical scan lines run across the screen. When choosing a picture advance speed, keep in mind that a fast advance speed will expand the size of the fish school horizontally on the screen and a slow advance speed will contract it. Note that the picture is not refreshed when picture advancement is stopped. Therefore, use caution when steering the vessel under this condition.

7

Image 14
Contents Echo Sounder 00080926502 Table of Contents Do not disassemble or modify the equipment Use the proper gain settingDo not open the equipment Use the proper fuseSafety Instructions for the Installer Use the specified power cableWord to LS-6100 Owners FeaturesForeword IiiStandard supply Name Type Code No Qty Remarks System configuration Equipment listsSystem Overview Optional equipment Name Type Code No Qty RemarksOperation Turning the Power On/OffHow to remove the hard cover Control DescriptionMode selection window Adjusting Display Contrast, BrillianceBrilliance/contrast adjustment window Choosing a Display, FrequencyMarker-zoom display Single frequency displayDual frequency display Nav data displays Bottom-zoom displayBottom-lock display Bottom-zoom displayHow automatic operation works Menu Operating ProcedureAutomatic Operation Choosing automatic operationRange offset Choosing the manual modeManual Operation Gain offsetUnit Basic Range Adjusting the gainChoosing Picture Advance Speed Shifting the rangeMeasuring Depth Scope DisplayClutter appearance Suppressing InterferenceSuppressing Low Level Noise Forms of interferenceWaypoints Erasing Weak EchoesWhite Line 49.6Setting destination waypoint Registering waypoint from the waypoint listEditing waypoints Using the Prog keyProg Key Erasing waypointsActivating an alarm AlarmsAlarm description Picture Color HueAlarm options Depth, temperature, speed setting windowAlarm menu Fish level optionsHow the alarm works Setting the DraftResetting Trip Distance Gain CompensationNav data window and item displayable Setting Up Nav Data DisplaysNAV Data Setup window Nav data displays 30 00.065N130 00.574E System Menu System & Installation MenusWater temperature display wide, F System menusNav window water temperature and speed Installation Menu Installation menuWaas options window Clear memory displayBottom level display MAINTENANCE, Troubleshooting Troubleshooting table TroubleshootingDiagnostics If… Then check …Test Pattern Test patternsThru-hull Mount Transducer InstallationDisplay Unit Acceptable transducer mounting locations Thru-hull mount transducer mounting Dimensions millimetersTypical thru-hull mount transducer installations Suitable transducer mounting locationsTransom mount transducer Mounting locations Transom Mount TransducerConstruction of fairing block Tape Transom mount transducerInside-hull Transducer Final preparation Pre-test for speed and temperatureOptional Triducer Tools and materials neededMounting location on single drive boat Installation of bracketHeight required at mounting location Positioning the templateAngle Shim with Taper down Taper up Adjusting10 11 transom angle Transom Parallel Transom angleCable routing Attaching the sensor to the bracketAttaching the sensor to the bracket Water temperature/speed sensor Optional Water Temperature/Speed SensorWiring Establishing the groundWater temp/speed sensor Optional equipmentPin arrangement on Nmea port Connection of converterFeeding data to RD-30 via the LS-6100 IEC 61162-1 Data SentencesWind sensor Specifications of the Echo Sounder LS-6100 Page