Furuno LS-6100 manual Optional Triducer, Final preparation, Pre-test for speed and temperature

Page 37

10.If the bottom is displayed in dark gray and the depth indication appears, the mounting location is suitable. Go to “Final preparation.”

11.If the bottom is not displayed in dark gray tone, the mounting location may be unsuitable. Do the following:

a)Press the [POWER/BRILL] key to turn off the power.

b)Gently dismount the transducer with a piece of wood.

c)Reattach the transducer elsewhere as shown in “Attaching the transducer.”

d)Check the installation again.

Final preparation

Support the transducer with a piece of wood to keep it in place while it is drying. Let the transducer dry 24-72 hours.

4.5 Optional Triducer

525ST-MSD

The optional triducer 525ST-MSD is designed for thru-hull mounting. For how to install this transducer see paragraph 4.2.

φ79 mm

133 mm 2.00"-12 UN

threads7 mm φ 51 mm

27 mm

140 mm

Triducer 525ST-MSD

525ST-PWD

The Transom Mount Transducer or TRIDUCER® Multisensor with Integral Release Bracket 525ST-PWD is manufactured by AIRMAR Co. These instructions are included with the sensor.

Pre-test for speed and temperature

Connect the sensor to the instrument and spin the paddlewheel. Check for a speed reading and the approximate air temperature. If there is no reading, return the sensor to your place of purchase.

Tools and materials needed

Scissors Masking tape Safety goggles Dust mask Electric drill Drill bit for:

Bracket holes: 4mm, #23, or 9/64”

Fiberglass hull: chamfer bit (preferred), 6mm, or 1/4”

Transom hole: 19mm or 3/4” (optional)

Cable clamp holes: 3mm or 1/8” Screwdrivers

Straight edge Marine sealant Pencil Zip-ties

Water-based antifouling paint (mandatory in salt water).

Mounting location

To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat. On slower heavier displacement hulls, positioning it farther from the centerline is acceptable.

Allow adequate space above the bracket for it to release and rotate the sensor upward.

30

Image 37

Contents Echo Sounder 00080926502 Table of Contents Do not open the equipment Use the proper gain settingDo not disassemble or modify the equipment Use the proper fuseUse the specified power cable Safety Instructions for the InstallerForeword FeaturesWord to LS-6100 Owners IiiSystem Overview System configuration Equipment listsStandard supply Name Type Code No Qty Remarks Optional equipment Name Type Code No Qty RemarksHow to remove the hard cover Turning the Power On/OffOperation Control DescriptionBrilliance/contrast adjustment window Adjusting Display Contrast, BrillianceMode selection window Choosing a Display, FrequencyDual frequency display Single frequency displayMarker-zoom display Bottom-lock display Bottom-zoom displayNav data displays Bottom-zoom displayAutomatic Operation Menu Operating ProcedureHow automatic operation works Choosing automatic operationManual Operation Choosing the manual modeRange offset Gain offsetChoosing Picture Advance Speed Adjusting the gainUnit Basic Range Shifting the rangeScope Display Measuring DepthSuppressing Low Level Noise Suppressing InterferenceClutter appearance Forms of interferenceWhite Line Erasing Weak EchoesWaypoints 49.6Registering waypoint from the waypoint list Setting destination waypointProg Key Using the Prog keyEditing waypoints Erasing waypointsAlarm description AlarmsActivating an alarm Picture Color HueAlarm menu Depth, temperature, speed setting windowAlarm options Fish level optionsResetting Trip Distance Setting the DraftHow the alarm works Gain CompensationNAV Data Setup window Setting Up Nav Data DisplaysNav data window and item displayable 130 00.574E 30 00.065NNav data displays Water temperature display wide, F System & Installation MenusSystem Menu System menusNav window water temperature and speed Installation menu Installation MenuBottom level display Clear memory displayWaas options window MAINTENANCE, Troubleshooting Diagnostics TroubleshootingTroubleshooting table If… Then check …Test patterns Test PatternDisplay Unit InstallationThru-hull Mount Transducer Typical thru-hull mount transducer installations Thru-hull mount transducer mounting Dimensions millimetersAcceptable transducer mounting locations Suitable transducer mounting locationsConstruction of fairing block Transom Mount TransducerTransom mount transducer Mounting locations Transom mount transducer TapeInside-hull Transducer Optional Triducer Pre-test for speed and temperatureFinal preparation Tools and materials neededHeight required at mounting location Installation of bracketMounting location on single drive boat Positioning the template10 11 transom angle Transom AdjustingAngle Shim with Taper down Taper up Parallel Transom angleAttaching the sensor to the bracket Attaching the sensor to the bracketCable routing Wiring Optional Water Temperature/Speed SensorWater temperature/speed sensor Establishing the groundPin arrangement on Nmea port Optional equipmentWater temp/speed sensor Connection of converterWind sensor IEC 61162-1 Data SentencesFeeding data to RD-30 via the LS-6100 Specifications of the Echo Sounder LS-6100 Page