Furuno FA-150 installation manual Changing Ship’s Mains Specifications, 100-115 VAC

Page 22

2.2Changing Ship’s Mains Specifications

The AC-DC power supply PR-240 is shipped ready for connection to a 200-230 VAC ship’s mains. If the ship’s mains is 100 VAC-115 VAC, change the tap connection and terminal board connection as below. Attach label supplied as accessories to the front panel according to the ship’s mains.

Ship’s mains

Tap connection

Terminal board

 

Label

 

 

 

 

 

AC200-230V

SEL 230 V

Below (a)

200-230 VAC

2.5-2.0 A

1φ

50/60 Hz

 

 

 

 

 

AC100-115V

SEL 115 V

Below (b)

100-115 VAC

4.0-3.5 A

1φ

50/60 Hz

 

 

 

 

 

 

 

 

 

 

 

Remove screw and cover.

Cover

Front panel

(a) 200-230 VAC

1Black

2Grey

Terminal board

(b) 100-115 VAC

1Black

2Grey

 

Relay

Coil

 

 

J4

3

 

2

 

1

 

1

SEL

 

115V

 

2

Heat sink

3

SEL

4

 

5

230V

 

6

 

 

7

 

 

8

 

 

Tap connection

(Pull out to disconnect.)

Front panel

Attach appropriate label.

AC FAIL:Connect to Alarm system.

Output Setting: Normal Open Set plug to 1 & 2 pins of J4

Normal Close Set plug to 2 & 3 pins of J4 (Factory setting)

(This setting is for serial no. 022736 and after.)

AC Power Switch

(When connecting DC input, note that the DC power is supplied if this swqitch is turned off.)

Note: The DC output load must be less than 8A.

16

Image 22
Contents Uais Transponder 00015008314 Safety Instructions System Configuration Category of the unitsStandard supply Equipment ListsIii Optional supply GPS antenna unit MountingAntenna Units Extending antenna cableHow to attach the connector N-P-8DFB for cable 8D-FB-CV How to attach connector N-P-8DFBVHF antenna Location CablingHorizontal separation distance Installation overview of GPS/VHF combined antenna How to attach the plug M-P-73 GPS/VHF combined antenna Mounting procedure GPS/VHF Combined antennaInstalling distributor unit DB-1 Desktop mounting Monitor UnitFlush mounting Type Name Type Code No QtyUais Transponder MountingPower Supply option Pilot Plug optionWiring ConnectionInternal ports of the Transponder Cable connection at transponder Fabrication of cables TTYCS-4, TTYCS-1Q and TTYCS-1How to attach wires to the Wago connector Fabrication of power cable DPYC-2.5Changing Ship’s Mains Specifications 100-115 VACInland AIS Specific Settings Setting and AdjustmentEntering activation key Password entry window Selecting AIS modeSetting blue sign status NAV Status menu initial sub-menuInitial Settings menu SET Blue Sign SW sub-menuSetting MMSI, IMO No., Name and Call Sign SET Mmsi sub-menuSetting GPS Antenna Position Setting COM port/PC port Setting Ship TypeSetting I/O Port Table Ship typePress the ENT key again to display the Mode setting window COM1 Long Range Priority setup Priority menuQuality setup Inland AIS only Attaching LAN KIT Option AttachingSetting LAN port for PC network Setting LAN port for Navnet 3D networkContinuous This page intentionally left blank IEC 61162-1/2 Data Sentences TransponderInland AIS specific sentences Input data/SentencesOutput data/Sentences Input+056#..#6+10/#64+#.5 # 8# #%%5514+5 Antenna Cable Set CP20-02700 CP20-02710 Antenna Cable Set CP20-00300 CP20-00310 Page Page Page Hatai Mar,2707 R.Esumi May 20 Page Jan 26/Oct/09 R.Esumi Page Page Page Page Page Transponder Unit
Related manuals
Manual 54 pages 24.96 Kb