Furuno 1832, 1942 manual Mounting Model 1932

Page 41

6.Remove the cable clamping plate by un-fastening four screws and removing a gasket.

Shield cover

Screws

Screws

4 pcs.

Cable clamping plate

7 pcs.

Shield cover

Gasket

 

Screws 7 pcs.

Screws 6 pcs.

Shield cover

Figure 6-5 Antenna unit, inside view

7.Pass the cable through the hole at the bottom of the radome base.

8.Secure the cable with the cable clamping plate and gasket. Ground the shield and vinyl wire by one of the screws of the cable clamping plate.

9.Connect the wire to the RF unit.

Figure 6-6 Signal cable, antenna unit side

Figure 6-7 RF unit

9.Attach the EMC core supplied as shown below.

Figure 6-8 How to attach EMC core

11.Fix the shield cover. Do not pinch the cable.

12.Attach the radome cover, aligning triangle mark on radome cover with that on radome base.

13.Loosely fasten the radome fixing bolts. You will tighten them after confirming magnetron heater voltage.

Mounting (Model 1932, 1942)

Figure 6-10 Typical antenna unit mounting

locations

1.Drill four fixing bolt holes (13 millimeters.), one cable entry hole (approx. 50 mil-limiters dia.) in the mounting platform. Seethe outline drawing.

27

Image 41
Contents Page 00080788713 Important Notices Radio Frequency Radiation Hazard Compliance with R&TTE Directive 1999/5/EC Foreword Table of Contents Model 1832 Specifications Vii SpecificationsViii OptionEquipment List Installation Materials Configuration of Model 1832/1932/1942 Xii How Radar Determines Range What is Radar?How Radar Determines Bearing Radar DisplayHow radar works Control Description Basic Operation125 NM Display Indication and MarkersTurning the Radar On/Off Economy modeTransmitting Stand-byAdjusting Receiver Sensitivity Adjusting Picture BrillianceAdjusting the A/C SEA Control reducing sea clutter Selecting the RangeAdjusting the A/C SEA control Adjusting the A/C Rain Control reducing rain clutterTip for adjusting the A/C SEA Adjusting A/C RainMeasuring the Range Erasing the Heading Line, North MarkBy range ring By cursorMeasuring the Bearing Using the Offset EBLBy EBL Predicting collision courseMeasuring range and bearing between two targets Cancelling shifted pictureShifting off centering the Picture Zoom Cancelling zoomPress the Menu key to close the menu Selecting the Presentation ModeBasic Menu Operation Magnifying Long Range Echoes echo stretch Echo TrailSelect OFF deactivate at Echo Trail on the menu Suppressing Radar InterferenceMentally create the guard zone you want to set Guard AlarmSelecting Pulsewidth Guard WatchmanGo into the Others menu, and set 15. Watchman for off Displaying Navigation DataFollowing summarizes the Other Menu Other Menu DescriptionFunction Keys Adjusting Brilliance of MarkersSuppressing Noise Outputting Target PositionIndirect Echoes Multiple EchoesSide-lobe Echoes Indirect echoes Blind and Shadow SectorsMaintenance & Troubleshooting Troubleshooting Self Test Unpacking the antenna unit Where the temperature is more than 70 CSiting, handling considerations Mounting ModelMounting platform Wiring and final preparationMounting Model 1932 Connections Fasten the cable gland assemblyWaveguide Groove Final preparationYou will need an Nmea cable Navigation aid, video sounder con- nectionMounting considerations MountingInput/Output Data List Heading signal can be connected to the HDG connectorHeading Sensor Connection Preparation Tick boxEntering antenna height Adjusting tune/videoWhen adjustment is completed, the mes- sages disappears Adjusting sweep timing Adjustment range0.000~3.239nm Adjusting MBS Adjustment 0.00~0.25Magnetron heater voltage Setting a blanking areaThis page is intentionally left blank Menu Tree ARP-10 Option Targets Limits, Visual alarm against lostTargets violating CPA/TCPA AP-4 Auto acquisition area is predefined between One minute after acquisition Vector still un- reliableAP-6 AP-7 Make sure the follows on Self Test menu ARP-10Not used Page Hatai Page Marine Radar Marine Radar