Furuno 1942, 1932, 1832 manual Important Notices

Page 3

IMPORTANT NOTICES

General

The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury.

Do not copy any part of this manual without written permission from FURUNO.

If this manual is lost or worn, contact your dealer about replacement.

The contents of this manual and equipment specifications can change without notice.

The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings.

Save this manual for future reference.

Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty.

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery(ies), see the chapter on Maintenance. Follow the instructions below if a battery(ies) is used.

In the European Union

The crossed-out trash can symbol indicates that all types of

 

 

batteries must not be discarded in standard trash, or at a trash

 

 

site. Take the used batteries to a battery collection site

 

 

according to your national legislation and the Batteries Directive

 

Cd

2006/66/EU.

 

 

 

In the USA

 

 

The Mobius loop symbol (three chasing arrows) indicates that

 

 

Ni-Cd and lead-acid rechargeable batteries must be recycled.

 

 

Take the used batteries to a battery collection site according to

Ni-Cd

Pb

local laws.

 

 

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycling symbols in the future.

i

Image 3
Contents Page 00080788713 Important Notices Radio Frequency Radiation Hazard Compliance with R&TTE Directive 1999/5/EC Foreword Table of Contents Model 1832 Specifications Vii SpecificationsViii OptionEquipment List Installation Materials Configuration of Model 1832/1932/1942 Xii Radar Display What is Radar?How Radar Determines Range How Radar Determines BearingHow radar works Control Description Basic Operation125 NM Display Indication and MarkersStand-by Economy modeTurning the Radar On/Off TransmittingSelecting the Range Adjusting Picture BrillianceAdjusting Receiver Sensitivity Adjusting the A/C SEA Control reducing sea clutterAdjusting A/C Rain Adjusting the A/C Rain Control reducing rain clutterAdjusting the A/C SEA control Tip for adjusting the A/C SEABy cursor Erasing the Heading Line, North MarkMeasuring the Range By range ringPredicting collision course Using the Offset EBLMeasuring the Bearing By EBLCancelling shifted picture Shifting off centering the PictureMeasuring range and bearing between two targets Zoom Cancelling zoomSelecting the Presentation Mode Basic Menu OperationPress the Menu key to close the menu Magnifying Long Range Echoes echo stretch Echo TrailSelect OFF deactivate at Echo Trail on the menu Suppressing Radar InterferenceGuard Alarm Selecting PulsewidthMentally create the guard zone you want to set Guard WatchmanGo into the Others menu, and set 15. Watchman for off Displaying Navigation DataFollowing summarizes the Other Menu Other Menu DescriptionOutputting Target Position Adjusting Brilliance of MarkersFunction Keys Suppressing NoiseMultiple Echoes Side-lobe EchoesIndirect Echoes Indirect echoes Blind and Shadow SectorsMaintenance & Troubleshooting Troubleshooting Self Test Mounting Model Where the temperature is more than 70 CUnpacking the antenna unit Siting, handling considerationsMounting platform Wiring and final preparationMounting Model 1932 Connections Fasten the cable gland assemblyWaveguide Groove Final preparationMounting Navigation aid, video sounder con- nectionYou will need an Nmea cable Mounting considerationsHeading signal can be connected to the HDG connector Heading Sensor ConnectionInput/Output Data List Preparation Tick boxAdjusting tune/video When adjustment is completed, the mes- sages disappearsEntering antenna height Adjusting sweep timing Adjustment range0.000~3.239nm Adjusting MBS Adjustment 0.00~0.25Magnetron heater voltage Setting a blanking areaThis page is intentionally left blank Menu Tree ARP-10 Option Limits, Visual alarm against lost Targets violating CPA/TCPATargets AP-4 Auto acquisition area is predefined between One minute after acquisition Vector still un- reliableAP-6 AP-7 ARP-10 Not usedMake sure the follows on Self Test menu Page Hatai Page Marine Radar Marine Radar