Kenmore 790.7944, 790.7942 manual Operating the Triple Ring Burner at the lowest setting

Surface Cooking

,,Operating Triple Ring Burner Conrd (some models)

• Operating the Bridge Burner (some models)

Operating the Triple Ring Burner at the lowest setting:

1.Push the right front surface control knob in and turn counterclockwise out of the OFF position (See Fig. 1).

2.Release the knob and rotate to the LITE position (See Fig. 1). Note: Although all electronic surface ignitors will spark at the same time, only the selected surface Burner will lite.

3.Visually check that the inner ring of the right front Burner has lit.

4.Continue to turn the control knob counterclockwise and stop at the first LO position. (Refer to Fig. 3). If a higher setting is need adjust accordingly.

Setting the Bridge Burner (for Bridge Burner models only):
The Bridge	Burner should		be used	with rectangular shaped cookware.				Cookware like the cast-	Left
iron Griddle	that is supplied		with your range is designed specifically						Rear
							for best results with the		Burner
Bridge Burner.									Left
The Bridge Burner feature			may be used to combine		the cooking power of 2 or if needed 3 gas				Burner
surface Burners located along the left-hand side of the glass cooktop.The left rear and left center
Burners are controlled		by the left rear surface Control Knob. In addition						the left front Burner may	Front
be added to the Bridge		Burner with the left front gas Control				Knob (See		Fig. 1).	Burner
Operating	the Bridge		Burner	(for Bridge	Burner	models	only):		_

1.Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Fig. 1).

2. Release the knob and rotate to the LITE position (See Fig. 1 on page 11). Note: All electronic	_	_
surface ignitors will spark at the same time. However, only the selected surface Burner will
lite.

3.Visually check that the left rear Burner has lit.

4.Contine to rotate the gas control knob clockwise past the first LO setting to the arrow marked

BRIDGE.

5. Visually check that both the left rear and left center Burners are lit. Fig. 1

6.When both burners are lit, continue to turn the control knob counterclockwise to adjust to the desired flame size for both burners together. Note: The markings between the 2rid Hi and LO settings on the left rear control knob adjust the flame size for both burners. Use the guide marks between the 2nd Hi and LO settings and adjust the flame size as needed (Refer to Fig. 3).

7.Add the left front Burner if needed. Once lit, visually adjust the flame size of the left front Burner to match the flame size of the Bridge Burner.

8.Place cooking utensil centered over the left-hand cooktop surface Burner Grate. DO NOT cook with any of the surface control knobs in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position).

Left Rear Left Rear			Bridge		Bridge
Burner	Burner		Burner		Burner
LITE	flame		UTE		flame
position	[=adjustment	7	position	F	adjustment =
,	/area	/	,		area t
Off	_Hi	Lo Bridge		Hi	Lo

Fig. 3 - Left Rear Bridge Burner Surface Control Knob markings

Note: Ifonly the left rear surface Burner is needed, follow the instructions provided below.

Operating only the Left rear Gas Surface Burner (for models equipped with Bridge Burner):

1.Place cooking utensil centered over the left-rear surface Burner Grate.

2.Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Fig. 2).

3.Release the knob and rotate to the LITE position. Note: Although all electronic surface ignitors will spark at the same time, only the left rear Burner will ignite.

4.Visually check that the left-rear burner has lit. Adjust the flame size by turning the control knob between the first HI and LO settings (See Fig. 3). DO NOT cook with the surface control knob in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position).

12