Kenmore 790.7942, 790.7944 manual Before Using Your Range

Page 7

Before Using Your Range

Assembly of Burner Heads & Burner Caps (for Deep Well Cooktop models only)

Your range is shipped with the Burner Heads and Burner Caps the Burner Heads and the cooktop.

a. Be sure to follow the installation instructions before installing and using your new range.

b. Remove all packing tape from cooktop area. Remove all Burner Caps and Burner Heads.

c. Discard all packing material located under Burner Heads. d. To replace Burner Heads & Caps, match the letters

located under center of Burner Caps with the letters located inside Burner Heads (Fig. 1).

in the correct locations. Packing material is located between

e. Match the letters stamped on Burner Skirts with Burner Heads and Burner Caps (See Fig. 1). Replace the Burner Heads and Caps on cooktop (See Fig. 2). Carefully align the Electrodes into slot or hole of each Burner Head (Fig. 3). Note: The Burner Heads should sit flat on Cooktop Burner Skirts.

f. Unpack Burner Grates and position on the cooktop.

Burner Skirt

Fig. 2

_ctrodesmust

Fig. 1

align into slot or

hole for each

Fig. 3

Burner

Head

Assembly of Burner Heads & Burner Caps (for Ceramic Glass Cooktop models only)

Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between the Burner Heads and burner skirts.

a. Be sure to follow the installation instructions before installing and using your new range.

b. Remove any packing tape from cooktop. Remove all Burner Caps and Burner Heads, except DO NOT RE- MOVE Burner Head for Triple Ring Burner (right-front burner position; See Fig. 4).

c. Discard any packing material located under the Burner Heads (except Triple Ring Burner position).

Burner

Head

Burner

Cap

d. Replace right rear Burner Head & Cap onto cooktop. Match the letter for the right-rear burner located inside of Burner Cap with the letter located inside Burner Head (only the right-rear position is marked with letter A- See Fig. 5). Carefully align the Electrode into slot of Simmer Burner Head (Fig. 7).

e. CAREFULLY (DO NOT FORCE) align the Bridge Burner Head over the 2 Bridge Burner Electrodes located on left side of the cooktop. After placing the Bridge Burner Head on the burner skirt, MAKE SURE that the Bridge Burner Head lies evenly on burner skirt.

f. Replace Bridge Burner Caps. These include 1 Bridge Burner Center Cap (rectangular shaped) and the 2 Bridge Burner End Caps (The Bridge Burner End Caps will fit at either the front or rear Bridge Burner Head locations). Make sure that the tabs located under the Bridge Burner Caps fall into the slots located in the Bridge Burner Head (See black arrows in Fig. 6) and that the Bridge Burner Caps lie flat and evenly on top the Bridge Burner Head.

g. Unpack Burner Grates. Position End Burner Grates on cooktop. Place Center Burner Grate between the end Burner Grates and check that all the Burner Grate legs lie flat on the glass cooktop surface.

Fig. 4

Bridge Burner

Head

I

2 Electrode hole locations

through

Bridge Burner

Head

Fig. 5

must align into slot or hole for Simmer Burner Head

Fig. 7

Fig. 6

Image 7
Contents Models, Modelos 790.7942 = color number, ntJmero de color Estufa a asContents For Your Safety Important Safety instructionsImportant Instructions for Using Your Cooktop Conversion to Liquefied Petroleum Gas or L.P. Gas Important Safety NoticeFor CERAMIC-GLASS Cook TOP Models some models Grounding InstructionsEn los EE.UU Before Using Your Range Your Elite Gas Range Features Include Range FeaturesTypes of Oven Racks Before Setting Oven ControlsOven Vent Location Removing & Replacing Oven RacksControl Locations of the Gas Surface Burners Before Setting Oven ControlsBefore Setting Surface Controls Air Circulation in the OvenTriple Ring Burner some models Setting Proper Surface Burner Flame SizeSurface Cooking Operating the Gas Surface BurnersOperating Bridge Burner For Bridge Models Only Operating the Triple Ring Burner at the lowest settingCare & Seasoning of the Griddle Setting Warmer Drawer ControlsUsing the Griddle Using the Warmer DrawerSetting Warmer Drawer Controls To Remove and Replace Warmer Warm & Ready TM Drawer Preparing Bread Dough for the Warmer DrawerControl Pad Settings Electronic Oven Control Pad FeaturesMinimum & Maximum To set the clock example below for Setting Oven ControlsSetting the Clock Setting Silent Control OperationTo cancel the Timer before the set time has run out Setting Continuous Bake or 12 Hour Energy SavingSetting Timer To set the Timer example for 5 minutesTo reactivate normal oven operation Setting Oven Lockout Feature IzcjlockoutTo activate the Oven Lockout feature Setting Temperature Display m Fahrenheit or CelsiusTo recalJ the cookie recipe stored under Key To Set the Recipe Recall FeatureTo quickly erase all stored recipes To set the Preheat temperature for 350F Setting PreheatTo set the Bake Temperature to 350F Setting BakeInstructions Setting Cook TimeSetting Delay Start Setting Oven Controls1st side To set the oven to broil at the default setting 550FRoasting Rack Instructions Setting the Food Categories FeaturesCooked Oven Controls SettingSetting Convection Bake To set the oven for Convection Bake Temperature To 350FTo set the Convection Convert feature Setting the Slow Cook Feature SettingtheOvenSabbathControlsDay Feature To set Warm & Hold Setting the Warm & Hold FeatureTo set Warm & Hold to turn on automatically Self-Cleaning Number pads Provided is a default 3 hour Self-Clean cycleStopping or Interrupting Self-Cleaning Cycle To adjust Oven temperature Higher Adjusting Oven TemperatureTo adjust the oven temperature lower Glass control panel General Care & CleaningHow to Clean SurfacesDoor Care Instructions Care & Cleaning of Stainless Steel some modelsCleaning the Cooktop, Burner Heads, Caps & Grates For heavy, burned on soil Ceramic Glass Cooktop only Changing Oven LightsBefore You Call Occurrence Before You CallSlow Cook Turkey Breast 1 turkey breast Recipes for Slow CookMY-HOME Your Home