Xantrex Technology XS400 manual To connect the DC cables

Page 39

Installing the XS400

To connect the DC cables:

Connect the DC cables as shown in Figure 2-5,in the order shown by the numbers.

1.Switch the On/Standby switch to the Standby () position.

2.Route the DC cables from the battery bank to the inverter. See “Step 6: Routing the DC Cables” on page 2–15.

3.Install a DC fuse and Disconnect or a DC circuit breaker in the positive side of the circuit within 18 inches of the battery.

This protects your battery and wiring in case of accidental shorting. (See “DC Fuse and Disconnect or DC Circuit Breaker” on page 2–9for recommended fuse size and type.) Open the DC fuse and Disconnect or turn off the DC circuit breaker.

4.Connect one connector on the POSITIVE (+) cable to the POSITIVE DC terminal on the inverter. Tighten the nut to a torque of

2.2–2.6 lbf-ft (3.0–3.5 Nm).

5.Connect the other connector to the positive (+) terminal DC fuse and Disconnect or to the DC circuit breaker. Use a wrench to tighten the connection according to the manufacturer’s recommendations. Test that the cable is secure.

6.Attach a short DC cable from the unconnected end of the DC fuse and Disconnect or DC circuit breaker. Tighten appropriately.

7.Observing polarity carefully, connect the other end of the fused cable to the POSITIVE (+) terminal of the battery. Tighten this connection to the battery manufacturer’s recommended torque.

8.Connect one connector on the NEGATIVE (–) cable to the NEGATIVE (–) battery terminal. Tighten the connection according to the battery manufacturer’s recommended torque.

9.Check that the polarity of the DC connections is correct: positive (+) on the inverter is connected to the positive (+) on the battery, and negative (–) is connected to the negative (–).

10.Connect the other connector of the NEGATIVE (–) cable onto the NEGATIVE (–) terminal on the XS400 Sine Wave Inverter.

11.Use a wrench to tighten the nut to a torque of 2.2–2.6lbf-ft(3.0–3.5 Nm). Test that the cable is secure.

975-0054-01-01

2–17

Image 39
Contents XS400 Sine Wave Inverter Page XS400 Sine Wave Inverter Date and Revision Organization PurposeScope AudienceConventions Used Related Information Acronyms and TerminologyPage General Precautions Important Safety InstructionsExplosive Gas Precautions Precautions When Working With BatteriesFCC Information to the User Page Contents Operation TroubleshootingSpecifications Battery Types and Sizes975-0054-01-01 Xiii Xiv Introduction How XS400 Works Premium Power and Ease of UseComprehensive Protection Protection feature This protection feature…Front Panel XS400 FeaturesBack Panel 2Back Panel of the XS400 2Back Panel Features3S400 Remote Switch S400 Remote SwitchInstallation Inverter IntroductionInstallation Codes Preparing for InstallationMaterials List Installation Tools and MaterialsMaterials for XS400 and S400 Remote Switch Installing the XS400 Designing Your InstallationOverview Choosing a Location Battery Requirements DC Cables To mount your XS400 Mounting Your InverterTo connect the chassis ground Connecting the Chassis GroundTo install the remote switch Installing the S400 Remote Switch3Connecting Cable to the XS400 To prepare the DC cables Getting Ready to Connect the DC CablesGuidelines for Routing the DC Cables Routing the DC Cables5Connection Order for DC Cables Connecting the DC CablesTo connect the DC cables To connect your AC appliances to the Gfci outlets Connecting Your Appliances to the Gfci OutletsTo hardwire the AC output connections Hardwiring the AC Output7Removing the 3 Screws on the Wiring Box Access Panel 8Completing the Hardwiring Connecting the AC Input Cord Performing Checks Prior to Initial Start-upTo connect the AC input cord Testing Your Installation To test the XS400 in invert modeTo test the XS400 in shore power mode Installation 9Inverter Dimensions Page 10S400 Remote Switch Mounting Template Scale approximately Page Operation Front Panel of the XS400 Front Panel FeaturesTurning the XS400 to Standby When Not in Use Operating the XS400Turning the XS400 to On or to Standby 2S400 Remote Switch Using the S400 Remote SwitchTo operate the XS400 in invert mode Operating in Invert ModeTo restart or operate several appliances Recovering from Low Battery Voltage ShutdownTo recover from a low battery voltage shutdown Restarting or Operating Multiple AppliancesTo operate in shore power mode Operating in Shore Power ModeStatus of Indicator Lights Monitoring the Indicator Lights3Resetting After a Fault or Shutdown Resetting After a Fault or ShutdownPage Troubleshooting Front Panel Troubleshooting Reference1Troubleshooting Reference for the XS400 1Troubleshooting Reference for the XS400 2Troubleshooting Reference for the S400 Remote Switch Page Specifications Physical Specifications of XS400 with Projections Electrical Specifications of XS400Fan Cooling System Physical Specifications of S400 Remote SwitchRegulatory Approvals Transfer CircuitPage BatterySizes Types Battery Types Automotive Starting BatteriesDeep-Cycle Batteries Battery Size Estimating Battery Requirements Battery Sizing ExampleTo determine how much battery capacity you need Battery Sizing Worksheet Using Multiple Batteries Two Separate Battery BanksTwo Batteries Connected In Parallel Battery Tips Battery Voltage State of Charge Warranty Warranty and Product InformationDisclaimer ProductExclusions Return Procedure Return Material Authorization PolicyInformation About Your System Out of Warranty ServiceIndex IX-2 975-0054-01-01 975-0054-01-01 IX-3 IX-4 975-0054-01-01 Page Xantrex Technology Inc