Lowrance electronic X100C, X105C DF manual 173.9 77.1 27.6 137.9 Millimeter 56.9 Inch

Page 32

Drill a 1-inch (25.4 mm) hole in the dash for the power, transducer and data cables. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in position and results in a neat in- stallation. Some customers, however, prefer to mount the bracket to the side of the cable hole — it's a matter of personal preference.

173.9

77.1

[3.03]

27.6

[1.09]

[6.85]

137.9

[5.43] 157.9

[6.22]

Millimeter

56.9

[2.24]

[Inch]

 

Front view (left) and side view (right) showing dimensions of the

X100C or X105C DF when mounted on gimbal bracket.

After drilling the hole, pass the transducer connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top.

If you wish, you can fill in the hole around the cables with a good ma- rine caulking compound. (Some marine dealers stock cable hole covers to conceal the opening.) No matter what type of installation you prefer, be sure to leave enough slack in the cables to allow tilting or swiveling the unit. If you choose to fill in the hole, be sure to position the cables against the rear edge of the hole as you apply the fill material.

Before positioning the bracket, be sure to hold the cables against the rear edge of the hole. Then, slide the bracket over the hole and butt the rear of the bracket base firmly against the cables, thus pinning them in place against the side of the hole. Finally, fasten the bracket to the dash. Attach the unit to the gimbal bracket using the supplied gimbal knobs and washers.

28

Image 32
Contents X100C X105C DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Page Read Me First Page How Sonar Works How to use this manual typographical conventions Menu CommandsArrow Keys KeyboardTransducer Installation PreparationsSingle-frequency transom installations Dual-frequency transom installationsSingle-frequency trolling motor installations Shoot-through hull installationsGood location Poor location Location Poor angle How low should you go?Deadrise less than Strakes Pad Shoot-thru-hull vs. Transom Mounting Transom Transducer centerline Hull bottomAssembling the bracket DotAligning the transducer on the transom TransducerTransducer bracket RatchetRatchets Assembling the transducer Drilling mounting holesAttaching transducer to transom TransomBottom Hull Flat-bottom hull Deep-vee hull Trolling Motor Bracket Installation single-frequency only TMB-S bracket Internal tooth washer Bolt Nut Flat washerTransducer aimed Hulls With Floatation MaterialsPartial fish arches Testing Determines Best Location Transducer location High speed Trolling speedTrue bottom Second bottom Manual range setting Shoot-thru-hull Installation Spread epoxy here Sand this surfaceOptional Temperature Sensor Optional Speed Sensor InstallationGood location Transom Bottom of hullPower Connections Powering a Nmea 2000 Buss Nmea 2000 Power cablePowering Your Unit Power Supply cable red and black wires Power connections for the units in this series Connecting to a Nmea 2000 Network Nmea 2000 Cable ConnectionsNmea 0183 Cable Connections To Nmea To sonar Network port Units Network SocketMounting the Unit Bracket, In-Dash or Portable Bracket Installation Front173.9 77.1 27.6 137.9 Millimeter 56.9 Inch Portable Installation Other AccessoriesIn-Dash Installation Face Cover Basic Sonar Operation KeyboardPower/lights on and off Main MenuMain Menu Pages Page Sonar Page, showing full sonar chart mode Basic Sonar Quick Reference Sonar Operations To adjust sensitivity Fish Symbols vs. Full Sonar Chart To Restore Factory SettingsOther Free Training Aids Page ASP Advanced Signal Processing To change the ASP levelAlarms Depth AlarmsZone Alarm Fish Alarm Chart Speed Calibrate SpeedColorLine Depth Cursor Thin or no ColorLine Wider ColorLineDepth Range Automatic Cursor line Depth boxTo switch to Manual Depth Range Depth Range ManualDepth Range Upper and Lower Limits To turn Auto Depth Range on againTo change the upper and lower limits Fish arches Area zoomedTo turn off upper and lower limits Fish I.D. Fish Symbols & DepthsFasTrack To turn on FishTrack To turn the Fish I.D. feature onFishTrack Symbols with FishTrack depths Frequency Change Transducer Frequency X105C DF onlyTo change the frequency setting to 50 kHz To change the frequency setting to 200 kHzHyperScroll Noise RejectionTo turn off displayed data Ping Speed & HyperScroll To change displayed data font sizeTo change Ping Speed To turn off HyperScroll Reset OptionsReset Water Distance Set Keel Offset Sensitivity & Auto Sensitivity Automatic SensitivityTo turn Auto Sensitivity back on To adjust sensitivity in auto modeTo adjust sensitivity in manual mode Sonar Color Mode Sonar Page & Sonar Chart Display OptionsTo change the chart mode color scheme Full Sonar ChartSplit Zoom Sonar Chart Digital Data/ChartCustomizing the Digital Data/Chart Screen FlashGraf Sonar Simulator FlasherSurface Clarity Stop ChartTo adjust the Surface Clarity level Upper and Lower Limits Zoom & Zoom BarZoom Pan Page Unit wont turn on Unit freezes, locks up, or operates erraticallyNo fish arches when the Fish I.D. feature is off NoisePage Page Supplemental Material Index Page Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-freeAccessory Ordering Information for all countries Visit our web site