Lowrance electronic X105C DF, X100C manual Accessory Ordering Information for all countries

Page 87

Accessory Ordering Information for all countries

To order Lowrance accessories such as power cables or transducers, please contact:

1)Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items.

To locate a Lowrance dealer near you, visit our web site, www.lowrance.com and look for the Dealer Locator. Or, you can consult your telephone directory for listings.

2)U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129 Call 1-800-324-0045 or visit our web site www.lei-extras.com.

3)Canadian customers can write:

Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario L4W2R7 or fax 905-629-3118.

Shipping Information

If it becomes necessary to send a product for repair or replacement, you must first receive a return authorization number from Customer Service. Products shipped without a return authorization will not be accepted. When shipping, we recommend you do the following:

1.Please do not ship the knobs or mounting bracket with your unit.

2.If you are sending a check for repair, please place your check in an envelope and tape it to the unit.

3.For proper testing, include a brief note with the product describing the problem. Be sure to include your name, return shipping address and a daytime telephone number. An e-mail address is optional but useful.

4.Pack the unit in a suitable size box with packing material to prevent any damage during shipping.

5.Write the Return Authorization (RA) number on the outside of the box underneath your return address.

6.For your security, you may want to insure the package through your shipping courier. Lowrance does not assume responsibility for goods lost or damaged in transit.

Image 87
Contents X100C X105C DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Page Read Me First Page How Sonar Works Keyboard How to use this manual typographical conventionsMenu Commands Arrow KeysPreparations Transducer InstallationShoot-through hull installations Single-frequency transom installationsDual-frequency transom installations Single-frequency trolling motor installationsHow low should you go? Deadrise less than Strakes PadGood location Poor location Location Poor angle Transom Transducer centerline Hull bottom Shoot-thru-hull vs. Transom MountingDot Assembling the bracketTransducerTransducer bracket Ratchet Aligning the transducer on the transomRatchets Drilling mounting holes Assembling the transducerTransom Attaching transducer to transomBottom Hull Flat-bottom hull Deep-vee hull TMB-S bracket Internal tooth washer Bolt Nut Flat washer Trolling Motor Bracket Installation single-frequency onlyHulls With Floatation Materials Partial fish archesTransducer aimed Transducer location High speed Trolling speed Testing Determines Best LocationTrue bottom Second bottom Manual range setting Spread epoxy here Sand this surface Shoot-thru-hull InstallationOptional Speed Sensor Installation Optional Temperature SensorTransom Bottom of hull Good locationPowering a Nmea 2000 Buss Nmea 2000 Power cable Power ConnectionsPowering Your Unit Power Supply cable red and black wires Power connections for the units in this series To Nmea To sonar Network port Units Network Socket Connecting to a Nmea 2000 NetworkNmea 2000 Cable Connections Nmea 0183 Cable ConnectionsMounting the Unit Bracket, In-Dash or Portable Front Bracket Installation173.9 77.1 27.6 137.9 Millimeter 56.9 Inch Other Accessories In-Dash InstallationPortable Installation Face Cover Keyboard Basic Sonar OperationMain Menu Power/lights on and offMain Menu Pages Page Sonar Page, showing full sonar chart mode Basic Sonar Quick Reference Sonar Operations To adjust sensitivity To Restore Factory Settings Fish Symbols vs. Full Sonar ChartOther Free Training Aids Page To change the ASP level ASP Advanced Signal ProcessingDepth Alarms AlarmsZone Alarm Fish Alarm Calibrate Speed Chart SpeedColorLine Thin or no ColorLine Wider ColorLine Depth CursorCursor line Depth box Depth Range AutomaticTo turn Auto Depth Range on again To switch to Manual Depth RangeDepth Range Manual Depth Range Upper and Lower LimitsFish arches Area zoomed To change the upper and lower limitsFish I.D. Fish Symbols & Depths FasTrackTo turn off upper and lower limits To turn the Fish I.D. feature on FishTrackTo turn on FishTrack Frequency Change Transducer Frequency X105C DF only Symbols with FishTrack depthsNoise Rejection To change the frequency setting to 50 kHzTo change the frequency setting to 200 kHz HyperScrollTo turn off displayed data To change displayed data font size Ping Speed & HyperScrollTo change Ping Speed Reset Options Reset Water DistanceTo turn off HyperScroll Set Keel Offset Automatic Sensitivity Sensitivity & Auto SensitivityTo adjust sensitivity in auto mode To adjust sensitivity in manual modeTo turn Auto Sensitivity back on Full Sonar Chart Sonar Color ModeSonar Page & Sonar Chart Display Options To change the chart mode color schemeDigital Data/Chart Split Zoom Sonar ChartCustomizing the Digital Data/Chart Screen FlashGraf Flasher Sonar SimulatorStop Chart To adjust the Surface Clarity levelSurface Clarity Zoom & Zoom Bar Upper and Lower LimitsZoom Pan Page Unit freezes, locks up, or operates erratically Unit wont turn onNoise No fish arches when the Fish I.D. feature is offPage Page Supplemental Material Index Page Page Page Lowrance Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service…Accessory Ordering Information for all countries Visit our web site