Furuno B042-008, B042-004, B042-016 manual Entering transducer data by transducer specifications

Page 32

3. INITIAL SETTINGS

Entering transducer data by transducer specifications

For dealer: When connecting the transducers which are not programmed, contact to PRODUCT SERVICE SECTION SERVICE CENTER, FURUNO HEAD OFFICE. For new transducer or other make of transducer see FURUNO information for further information.

Note 1: If you are continuing from paragraph 3.1, go to step 2.

Note 2: If you have already entered transducer settings and wait to reconfirm them turn on the power while pressing any key.

Note 3: The transducers of 54 – 64 kHz, 112 – 122 kHz and 171 – 181 kHz cannot be connected to the FCV-1100L because of noise. (Available range: HIGH; 40 – 220 kHz, LOW; 25 –220 kHz).

1.Turn on the power.

2.Press any key.

3.Press ["] to select XDCR SELECT, and then press [+] or [-] to show the dialog below.

XDCR TYPE MANUAL

4.Press [+] to select MANUAL, and then press [!] or ["] to close the dialog box. The display should now look something like the one below.

XDCR SELECT INSTALLATION DEMO

XDCR SELECT

:

MANUAL

 

[HIGH]

 

 

 

CONNECTION

: NOT CONNECTED

FREQ

: ---kHz

[LOW]

 

 

 

CONNECTION

: NOT CONNECTED

FREQ

: --- kHz

POWER REDUCTION : OFF

Select how to set XDCR type.

[-/+]: Change setting, Turn OFF to exit

Menu for manual entry of transducer specifications

5.Do the following for both the high and low frequency transducers, or whichever transducer is installed.

a)Press ["] to select CONNECTION of [HIGH] or [LOW], and then press [+] or [-] to open the dialog box.

NOT CONNECTED CONNECTED

b)Use [+] or [-] to select CONNECTED, and then press [!] or ["] to close the dialog box.

c)Press ["] to select FREQ, and press [+] or [-] to display the frequency setting dialog box.

---kHz

3-6

Image 32
Contents Color LCD Sounder 00080922000 Safety Instructions Damage to the transducer may result Table of Contents System Configuration Options Equipment ListsStandard supply Available transducers Vii Viii KW/2 kW transducer 28/45 Steel 28F-8 Steel 50B-6/6B Xii Xiii Xiv Mounting considerations MountingDisplay Unit Mounting procedure Removing the display unit from the mounting baseFlush mounting Flush mounting display unitTransducer Water Temperature Sensor optionHow to mount transom mount water Temperature sensor T-02MTB Thru-hull mount water temperature sensor T-02MSB, T-03MSB Water temperature/speed sensor ST-02MSB, ST-02PSB Wiring Wiring diagram for standard-type FCV-1100LWiring Standard Equipment Power cableTransducer GroundWiring Optional Equipment Input/Output SentencesThis page is intentionally left blank Initial display screen Initial SettingLanguage Setting Transducer Data Maker Frequency Type RemarksInstallation main menu Entering transducer data by transducer model numberScroll bar Dialog box for 200 kHzTerminal board Transducer settingDisplay unit, rear view Entering transducer data by transducer specifications Menu for manual entry of transducer specificationsWater Temperature Sensor Setting Temp Setting menuSensor Nav Data, Heading Sensor Setting NAV Data Setting menuTrue MAG Installation menu Propagation VelocityDemonstration Mode Demo menuRestoring Default Settings This page is intentionally left blank Appendix Transducer 50BL-12/50BL-24H AP-1Appendix NEW BLT Transducers AP-2AP-3 Appendix 2 NEW BLT TransducersAP-4 Page Page Page Page Nov Page