Furuno B042-008, B042-004, B042-016 manual Nav Data, Heading Sensor Setting, NAV Data Setting menu

Page 35

3. INITIAL SETTINGS

3.4Nav Data, Heading Sensor Setting

Select navigator and heading sensor used as below.

1.Turn on the power and turn the [FUNCTION] switch to the MENU position.

2.Press [!] and [+] to select SYSTEM at the top of the screen.

3.Press ["] to select NAV DATA SETTING, and then press [+] to open that menu. (If a heading sensor is connected but not a navigator, go to step 18.)

DISP ALM TX/RX E/S SYSTEM

NAV DATA SETTING

 

SPEED UNIT

 

:

kt

 

 

SPEED INPUT

: SENSOR

 

SPEED ADJUST

: +0% (-50 +50)

 

SPEEDOUTPUT

: ON

 

SPEED INFO

: OFF

 

NMEA VERSION

: Ver 2.0

 

NAV DATA

: AUTO

 

COURSE

: TRUE

 

TLL OUTPUT

: OFF

 

 

 

 

 

 

 

Select speed unit.

 

 

 

[-/+]: Change set, [EXIT]: Exit

NAV DATA SETTING menu

4. The cursor is selecting SPEED UNIT; press [+] or [-] to open the dialog box.

kt km/h MPH

5.Use [-] or [+] to select the speed unit, and then press [!] or ["] to close the dialog box.

6.Press ["] to select SPEED INPUT, and then press [+] or [-] to open the dialog box.

SENSOR NMEA

7.Use [+] or [-] to select the source of speed data, and then press the [!] or ["] to close the dialog box.

SENSOR: Speed/temperature sensor

NMEA: Speed data input from the equipment connected.

8. Press ["] to select SPEED ADJUST, and the press [+] to open the dialog box.

+0.0

9.You may offset speed data to further refine its accuracy. This is not possible when the speed input is “NMEA”.

a)Watch the speed sensor readout on the monitor (if it is not displayed set SPEED INFO to ON) and compare it with known value.

b)Use [+] or [-] to enter the difference found in a) above. For example, if the indication of the FCV-1100L is +5 % faster than the actual value, enter –5.

3-9

Image 35
Contents Color LCD Sounder 00080922000 Safety Instructions Damage to the transducer may result Table of Contents System Configuration Options Equipment ListsStandard supply Available transducers Vii Viii KW/2 kW transducer 28/45 Steel 28F-8 Steel 50B-6/6B Xii Xiii Xiv Mounting considerations MountingDisplay Unit Removing the display unit from the mounting base Mounting procedureFlush mounting display unit Flush mountingTransducer Water Temperature Sensor optionHow to mount transom mount water Temperature sensor T-02MTB Thru-hull mount water temperature sensor T-02MSB, T-03MSB Water temperature/speed sensor ST-02MSB, ST-02PSB Wiring diagram for standard-type FCV-1100L WiringGround Wiring Standard EquipmentPower cable TransducerInput/Output Sentences Wiring Optional EquipmentThis page is intentionally left blank Initial display screen Initial SettingLanguage Setting Maker Frequency Type Remarks Transducer DataEntering transducer data by transducer model number Installation main menuDialog box for 200 kHz Scroll barTerminal board Transducer settingDisplay unit, rear view Menu for manual entry of transducer specifications Entering transducer data by transducer specificationsTemp Setting menu Water Temperature Sensor SettingSensor NAV Data Setting menu Nav Data, Heading Sensor SettingTrue MAG Propagation Velocity Installation menuDemo menu Demonstration ModeRestoring Default Settings This page is intentionally left blank AP-1 Appendix Transducer 50BL-12/50BL-24HAP-2 Appendix NEW BLT TransducersAppendix 2 NEW BLT Transducers AP-3AP-4 Page Page Page Page Nov Page