Yamaha Yamaha Mixing Consol, M2500 Stereo/monaural master section, Stereo section, MONO/C section

Page 20

Control panel

Stereo/monaural master section

This section controls the signals that are output from the rear panel ST OUT L/R and MONO/C OUT jacks (page 28).

15

MATRIXMATRIX

	CHECK	CHECK
2	ON	ON	6
	ON/EDIT	ON/EDIT
	10	10
	5	5
	0	0
	5	5
	10	10
	20	20
	30	30
	40	40
3	50	50	8
3	60	60	8
4	AFL	AFL	7
4

STEREO MONO/C

STEREO section

A MATRIX switch

If this switch is on (), the post-fader ST OUT L/R signal will be sent to the matrix (page 18).

B ON/EDIT switch / ON, CHECK indicators

The function of this switch and these indicators will change depending on the mode of the M2500.

●In normal mode

You can use the ON/EDIT switch to turn ST OUT L/ R on/off. When this is switched on/off, the ON indi- cator will be lit/dark to indicate the status. Channels that are switched off will not send any signals to the ST OUT L/R jacks or to the matrix.

●In check mode

When a scene (which contains the on/off state of the ON/EDIT switches) is selected, the on/off status memorized in that scene will be indicated by the lit/ dark status of the CHECK indicator. In check mode, you can also use the ON/EDIT switch to switch the CHECK indicator between lit/dark. (The current on/ off setting will not be affected.) For details on check mode, refer to page 32.

CFader

This adjusts the ST OUT L/R output level.

DAFL switch

Using this switch, the signal sent to the ST OUT L/R jacks can be monitored from the MONITOR OUT/ PHONES jacks. If the PFL switches of all input chan- nels are off, turning this AFL switch on (the indicator above the switch will light) will allow you to monitor the output signal of the STEREO section from the MONITOR OUT/PHONES jacks. Use the MASTER PFL switch of the monitor section to switch the mon- itor signal between pre/post-fader.

MONO/C section

E MATRIX switch

If this switch is on (), the post-fader MONO/C sig- nal will be sent to the matrix (page 18).

F ON/EDIT switch / ON, CHECK indicators

The function of this switch and these indicators will change depending on the mode of the M2500.

●In normal mode

You can use the ON/EDIT switch to turn MONO/C OUT on/off. When this is switched on/off, the ON indicator will be lit/dark to indicate the status. Chan- nels that are switched off will not send any signals to the MONO/C jack or to the matrix.

●In check mode

When a scene (which contains the on/off state of the ON/EDIT switches) is selected, the on/off status memorized in that scene will be indicated by the lit/ dark status of the CHECK indicator. In check mode, you can also use the ON/EDIT switch to switch the CHECK indicator between lit/dark. (The current on/ off setting will not be affected.) For details on check mode, refer to page 32.

GFader

This adjusts the output level of MONO/C.

16 M2500—Owner’s Manual

Image 20

Contents Mixing Console Nederland Netherlands Important Information Operating NotesKeep This Manual For Future Reference Read the Following Before Operating M2500Page Contents IntroductionFeatures of the system Control panel Input channel sectionMonaural input channels AUX 1-AUX 14 controlsPAN control PRE switchesChannel assign switches ON/EDIT switch / ON, Check indicators PEAK/NOM/SIGNAL indicatorsPFL pre-fader listen switch Channel faderGain B control B switchStereo input channels BAL control If the ST switch is onIf a 1-2/3-4/5-6/7-8 switch is on Input a ST CH Input B Mono AFL after fader listen switches GROUP/AUX master sectionAUX 1-6 section AUX 1-6master fadersOn switch AFL switchGROUP/AUX Flip switch= Group GROUP/AUX Flip switch= AUXG1/A7-G8/A14 section Matrix switch AFL after fader listen switch FaderWhen AUX is selected GROUP/AUX Flip switchWhen Group is selected MATRIX/ST/MONO/LCR Matrix switch Stereo/monaural master sectionStereo section MONO/C sectionMatrix Monitor Matrix section ST L/R controlsMONO/C control G1/A7-G8/A14 controlsMonitor signal priority order Master indicatorMaster PFL switch Monitor sectionPhones jack +R switchPhones headphone control MONO/C switch Oscillator on switchTalkback/oscillator section MIC jackA7-14/G1-8 switch AUX 1-6 switchG1-8/A7-14 switch Meter select sectionRecall switch Store switchCheck switch Direct Recall 1-8 switches+15V/-15V/+12V indicators Phantom Master indicatorMeter bridge MONO/C level meterNominal input Rear panelInsert I/O jacks Input B jacks Stereo input channel input/ output jacksInput a jacks Input jacks Master section input/output jacks AUX/GRP OUT jacksGRP/AUX OUT jacks Matrix OUT jacksST OUT, MONO/C OUT jacks Monitor OUT jacksSUB in Matrix jacks SUB in ST L/R, MONO/C jackMidi connectors Phantom Master switchDC Power Input connector Lamp connectorModes of the scene memory function What is scene memory?Scene Memory function Operation in Normal mode Using Direct Recall to recall a sceneRecalling a scene Storing a sceneCheck mode operation Checking the contents of a scene you wish to recallPress the Check key once again to return to Normal mode Editing and storing the scene you are checkingUtility items Utility mode proceduresBasic procedure in Utility mode Midi channel Program change transmission/reception OFF/on/LoCControl change transmission/reception OFF/GrP/on Program change reception omni on/off On/oFFControl change table Control No Channel Mute groupMute group Mute groupsDirect recall Using mute groups About the local control cir- cuitError messages Speciﬁcations General speciﬁcationsOutput specifications Input/output characteristicsInput specifications Included items Connector wiringOther Rear DimensionsFront Midi data format Midi Implementation Yamaha Corporation