Tascam FW-1082 owner manual System Requirements, Box, Nomenclature used in the manual

Page 8

1 – Introduction

NOTE

We strongly suggest that although a “daisy-chain” con- nection is provided, that the FW-1082 is the only unit connected to the FireWire port.

Always perform all FireWire connections and disconnec- tions with the power to both the FW-1082 and the com- puter turned off. If connections are made or broken

with power to the FW-1082 or computer turned on, this may result in your computer crashing, or “freezing” and possible loss of data.

When turning the power of the FW-1082 on and off when it is connected to the computer, turn on the power before launching the DAW software, and quit the software before turning off the FW-1082.

System Requirements

The FW-1082 is supported under Windows XP and Windows 2000. The FW-1082 is not supported under Windows 98 or Windows ME.

In the case of Windows 2000, you must be running SP3 or SP4 and then install the supplied Hotfix. Win- dows 2000 SP5 includes the Hotfix, so there is no need to install it separately. For Windows XP, you

must be running SP1 and then install the supplied Hotfix. Windows XP SP2 includes the Hotfix, so there is no need to install it separately.

On the Mac, the FW-1082 is supported under Mac OS X version 10.2.8 or later. Earlier versions of Mac- intosh operating systems are not supported.

In The Box

The FW-1082’s box contains the items listed below. When opening the package please be certain all the items listed are included. If any items are missing, please consult your TASCAM dealer.

FW-1082

AC power adapter (PS-1225B) and cable

IEEE 1394 6-pin to 6-pin cable

A CD-ROM containing the driver and utility soft- ware and documentation for the FW-1082 (Win- dows and Mac compatible).

A second CD-ROM containing the Cubase LE application.

This manual

The Setup Guide

Warranty card.

Nomenclature used in the manual

Within this manual, the following typographic con- ventions are used:

The name of a control or connector on the unit is written in the following way: LINE/MIC.

The name of a control or connector on another unit is written in the following way: AUX IN.

When referring to the screen display of the host computer, we refer to any prompts, messages, etc.

in the following typeface: Press any key to

continue.

The names of keys to be pressed on the computer

keyboard are written in this typeface with square brackets enclosing them [F1].

Keys that are to be pressed together are joined by a

+ symbol, so that [Ctrl]+[F1] means “press and hold the Control key and press the F1 key”.

Whenever we refer to the software application to control and set up the FW-1082, we refer to it as the “Control Panel” or the “software Control Panel”.

If you have to type something into the computer, we write it this way: FILENAME.EXT.

There are three control surface modes. These are written in this manual as follows, to match the labels of the respective mode keys: COMPUTER (DAW control, etc.), MIDI CTRL (MIDI control) and MON MIX (monitor mixer).

8 TASCAM FW-1082 Owner’s Manual

Image 8
Contents DAW Control Surface / FireWire Audio-MIDI Interface Important Safety Precautions For CanadaImportant Safety Instructions Contents Control Panel Troubleshooting and Support Specifications 1IEEE.1394 4-pin and 6-pin connectors Table of FiguresOverview FeaturesIntroduction Nomenclature used in the manual System RequirementsBox Copyright, etc Software application notesSpecial notes for touch-sensitive faders Parts of the FW-1082 Front PanelChannel controls Encoders and controls Monitoring and indicatorsMode controls DAW transport controls Monitoring Phones Line inputs and inserts Power jackRear panel Mic inputs and phantom power switch Foot switch jack Foot SWCoaxial Digital audio I/O in and OUT Monitoring and phonesPower jack and switch FW-1082 outputs produce a thump when the power is turned onFunctional Overview Control Surface ModesGlobal Controls Dedicated Computer ControlsSetting and checking clock rates Dedicated Modifier KeysNative Protocol Computer Control Mode General NotesControl Surface Modes and Operation Mackie Emulation Protocol HUI Emulation ProtocolMidi Control Mode General Notes Cursor keysProgramming Keys Setting the Midi message typeProgramming the Midi Control Messages Programming Encoders Controller On/OffBanking Monitor Mix Mode General NotesProgramming Faders Monitoring Setups Making mixer settingsSetting the master fader to 0dB unity gain Audio I/O and the Monitor MixerSetting Input levels Master Fader Affects Anlg LR Gain Settings tabControl Panel Midi Programming tab Quick Start tab Windows onlyCoreAudio tab OS X only Core Audio tab for OSControl surface troubleshooting Troubleshooting and SupportAudio troubleshooting Contacting Us Specifications Analog I/OMisc. I/O Overall System SpecificationsDigital I/O Physical, etc. specifications Analog performanceDimensional drawing Dimensions of the FW-1082Page FW-1082