Sony PCS-1P Turning On, Launcher menu, Standby Mode Function, To release the standby mode

Page 17

1-4-5. Turning On

1.Turn on the TV monitor.

If the IR repeater is installed in the TV monitor, set the TV monitor to standby mode. The TV monitor will turn on simultaneously when the Communication Terminal is turned on.

2.Turn on the power of any other equipment to be used for the videoconference.

3.Set the power switch on the right side of the Communication Terminal to the on position (I).

Power switch

POWER indicators (Light in green.)

The Communication Terminal turns on after a while. Three indicators on the front of the Communication Terminal and the POWER indicator on the camera light, then only the POWER indicators on both units remain on in green. The launcher menu will appear on the monitor screen and the picture shot by the local camera will also appear in the launcher menu.

Launcher menu

Connect

 

Phone Book

 

Dial

 

Menu

Angle Adj.

Show Help

 

IP:0.0.0.0

ISDN:012345678912

Video:Main

Audio:MIC(INT)+AUX

m

.After the power is turned on, the camera moves

automatically for trial operation. Be careful not to catch your finger.

.If you use force to prevent the camera moving, it may not resume moving and not output a signal to the

Communication Terminal. In this case, turn off the Terminal, and turn it on again.

.When you turn on the power of the Communication Terminal for the first time after installation, the setup

wizard will appear after the self-diagnosis is completed. Set up your system following the wizard.

.For setups using the wizard, see “Setting Up the System for the First Time - Initial Setup Wizard” on page 1-14.

Standby Mode Function

To save power the Communication Terminal will enter standby mode if you do not operate it for a specified period of time.

When the Communication Terminal is in standby mode, the POWER indicator lights in orange. Once the Communication Terminal receives a call, the standby mode is automatically released.

To release the standby mode

Press the I/O button on the Remote Commander.

To specify the standby time

Specify the time that you want the system to remain on before entering into standby mode (1 to 99 minutes) using “Standby Time” in the General Setup menu. If you do not want the system to enter the standby mode, set “Standby Mode” in the General Setup menu to “Off”.

For the “Standby Time” and “Standby Mode” settings, see

“General Setup Menu” on page 1-17. m

.The POWER indicator on the camera goes off when the system enters standby mode.

.If you use a Sony TV monitor with the IR repeater installed under the remote sensor, the TV monitor will enter standby mode together with the Communication Terminal.

PCS-1/PCS-1P

1-13

Image 17
Contents PCS-1 PCS-1P Warnung Table of Contents Technical Data Camera Range Lay Out the Videoconferencing RoomTop view horizontal range at maximum zoom- out Side view vertical range at maximum zoom-outHighly directional range of microphone Microphone layout examples Installation of document stand PCS-1/PCS-1P Lighting Considerations Operating EnvironmentLayout Considerations Flowchart of Installation System Connections When Used in LAN 100BASE-TX/10BASE-TTerminal When Used in IsdnInitialization Inserting Batteries into the Remote CommanderRemoted sensor PCS-1/PCS-1P To release the standby mode Standby Mode FunctionTurning On Launcher menuProtocol When the Power was First Turned on after InstallationArea Code To go back to the previous wizard To cancel the settingLAN System SettingMODE1 DSB Flowchart of Opening Test Controller Outgoing Procedure of IsdnStart meeting is displayed, Screen Incoming Procedure of IsdnOutgoing Procedure of LAN Start meeting is displayed, Incoming Procedure of LAN Operation procedure Section MaintenanceTrouble Separation of ComponentsYES SS-02 Does Power Amber lamp of main unit light? Power is not turned on during automatic incoming. Isdn Power is not turned on during automatic incoming. LAN Is the monitor SS-06 Is the launcher menu No function can be operated using a remote controller Camera on the local side cannot be operated No line is connected. Isdn No line is connected. LAN Is the volume of the monitor TV turned down? SS-12 SS-13 Is video input properly set? Check the terminal of the other end Is the setting of the video signal input correct? Operation Log Operation log using commercial PCPCS-1/PCS-1P PCS-1/PCS-1P PCS-1/PCS-1P PCS-1/PCS-1P Operation log using commercial PC PCS-1/PCS-1P PCS-1/PCS-1P PCS-1/PCS-1P PCS-1/PCS-1P Updating of Software Updating Using Memory StickFor system reset Service ModeFor erasure of an address book and setting To stop setting For command inputContents of functions For loading of applicationPCS-1/PCS-1P Page Example of system Connection via HubOFF Connection via Router OFF Connection via Dhcp OFF LAN1 LAN2 Connection via GatekeeperOFF Connection via Dhcp and Gatekeeper OFF During Opposed Connection Specified Value PCS-1/1P Port Number UsedPort number at first point Port number at N’th point During Use of Internal MCU Function Specified ValueTable of connection between PCS-1 and Catalyst Setting of PCS-1 and HUBPage Page Sony Corporation
Related manuals
Manual 8 pages 19.36 Kb

PCS-1, PCS-1P specifications

The Sony PCS-1P and PCS-1 are cutting-edge video conferencing solutions designed for businesses seeking high-quality communication tools. Tailored for professional environments, these units facilitate seamless connectivity, encouraging collaboration without geographical barriers.

One of the standout features of the PCS-1P and PCS-1 is their remarkable video quality. Both models support high-definition video, providing sharp, crystal-clear images that enhance the remote communication experience. This clarity is especially beneficial for presentations, allowing participants to see details in charts and graphics with precision. The PCS-1P model specifically offers 720p HD resolution, ensuring that every meeting feels as face-to-face as possible.

In terms of audio, Sony has equipped both the PCS-1P and PCS-1 with advanced audio technologies. These units include high-quality microphones that capture sound from all corners of the room, coupled with noise cancellation features that eliminate background distractions. This results in a clear and engaging communication experience, essential for effective collaboration.

Another significant characteristic of the PCS-1 series is its user-friendly interface. The systems are designed for easy setup and operation, making them accessible even for less tech-savvy users. An intuitive remote control allows users to manage video calls effortlessly, adjusting settings without fumbling through complicated menus.

Connectivity is also a hallmark of the PCS-1P and PCS-1. These devices can connect to a wide range of networks, including IP networks, offering flexibility in how and where users can engage. Additionally, they support both SIP and H.323 protocols, ensuring compatibility with various other video conferencing systems and platforms.

Furthermore, the PCS-1P and PCS-1 models boast built-in record and playback functionalities, allowing users to capture meetings for future reference. This feature is invaluable for businesses that require a record of discussions and decisions made during video conferences.

With their robust feature set, including reliable connectivity, high-definition video and audio quality, and ease of use, Sony's PCS-1P and PCS-1 video conferencing systems stand out as leading solutions for modern enterprises. They not only enhance communication but also promote productivity and collaboration across teams, regardless of their physical location. In a globally connected business environment, these tools represent a strategic asset for any organization aiming to improve its communication efforts.