Sony RS-232C manual Level Down 43H 4CH 56H 2DH ‘CLV-’, Fader level 2nd byte

•Fader level (2nd byte)

Set the fader level [dB].

LEVEL		LEVEL		LEVEL		LEVEL
-∞	30[H] (‘0’)	-20.0	40[H] (‘@’)	-4.5	50[H] (‘P’)	+3.5	60[H] (‘`’)
-70.0	31[H] (‘1’)	-19.0	41[H] (‘A’)	-4.0	51[H] (‘Q’)	+4.0	61[H] (‘a’)
-60.0	32[H] (‘2’)	-18.0	42[H] (‘B’)	-3.5	52[H] (‘R’)	+4.5	62[H] (‘b’)
-55.0	33[H] (‘3’)	-17.0	43[H] (‘C’)	-3.0	53[H] (‘S’)	+5.0	63[H] (‘c’)
-50.0	34[H] (‘4’)	-16.0	44[H] (‘D’)	-2.5	54[H] (‘T’)	+5.5	64[H] (‘d’)
-45.0	35[H] (‘5’)	-15.0	45[H] (‘E’)	-2.0	55[H] (‘U’)	+6.0	65[H] (‘e’)
-40.0	36[H] (‘6’)	-14.0	46[H] (‘F’)	-1.5	56[H] (‘V’)	+6.5	66[H] (‘f’)
-35.0	37[H] (‘7’)	-13.0	47[H] (‘G’)	-1.0	57[H] (‘W’)	+7.0	67[H] (‘g’)
-32.5	38[H] (‘8’)	-12.0	48[H] (‘H’)	-0.5	58[H] (‘X’)	+7.5	68[H] (‘h’)
-30.0	39[H] (‘9’)	-11.0	49[H] (‘I’)	0	59[H] (‘Y’)	+8.0	69[H] (‘i’)
-27.5	3A[H] (‘:’)	-10.0	4A[H] (‘J’)	+0.5	5A[H] (‘Z’)	+8.5	6A[H] (‘j’)
-25.0	3B[H] (‘;’)	-9.0	4B[H] (‘K’)	+1.0	5B[H] (‘[’)	+9.0	6B[H] (‘k’)
-24.0	3C[H] (‘<’)	-8.0	4C[H] (‘L’)	+1.5	5C[H] (‘\’)	+10.0	6C[H] (‘l’)
-23.0	3D[H] (‘=’)	-7.0	4D[H] (‘M’)	+2.0	5D[H] (‘)’)
-22.0	3E[H] (‘>’)	-6.0	4E[H] (‘N’)	+2.5	5E[H] (‘^’)
-21.0	3F[H] (‘?’)	-5.0	4F[H] (‘O’)	+3.0	5F[H] (‘_’)

Example: When changing the sound volume of the MASTER A to 0 dB

43[H] 4C[H] 56[H] 4C[H] 40[H] 59[H] 0D[H] (‘C L V L @ Y CR’)

LEVEL DOWN: 43[H] 4C[H] 56[H] 2D[H] (‘CLV–’)

This command is used to decrease the sound volume of the specified channel.

When this comma is sent, the sound volume keeps decreasing. When the LEVEL UP/DOWN STOP command that is described later, is sent, the sound volume stops decreasing.

Variable range of a sound volume is from – ∞ to +10 dB when the sound volume is set to the reference level 0 dB. When the power of the SRP-X700P is turned off, the sound volume level is reset to 0 dB.

•Packet format

43[H] 4C[H] 56[H] 2D[H] “parameter” 0D[H]

• Parameter

CHANNEL		CHANNEL
MIC1/WL1 INPUT	30[H] ( ‘0’ )	LINE OUTPUT5	3C[H] ( ‘<’ )
MIC2/WL2 INPUT	31[H] ( ‘1’ )	LINE OUTPUT6	3D[H] ( ‘=’ )
MIC3 INPUT	32[H] ( ‘2’ )	LINE OUTPUT7	3E[H] ( ‘>’ )
MIC4 INPUT	33[H] ( ‘3’ )	LINE OUTPUT8	3F[H] ( ‘?’ )
MIC5/LINE1 INPUT	34[H] ( ‘4’ )	MASTER A	40[H] ( ‘@’ )
MIC6/LINE2 INPUT	35[H] ( ‘5’ )	MASTER B	41[H] ( ‘A’ )
LINE 3 INPUT	36[H] ( ‘6’ )	REMOTE 1	42[H] ( ‘B’ )
LINE 4 INPUT	37[H] ( ‘7’ )	REMOTE 2	43[H] ( ‘C’ )
LINE OUTPUT1	38[H] ( ‘8’ )	REMOTE 3	44[H] ( ‘D’ )
LINE OUTPUT2	39[H] ( ‘9’ )	REMOTE 4	45[H] ( ‘E’ )
LINE OUTPUT3	3A[H] ( ‘:’ )	REMOTE 5	46[H] ( ‘F’ )
LINE OUTPUT4	3B[H] ( ‘;’ )	REMOTE 6	47[H] ( ‘G’ )

Specify the channel that you want to use, as the parameter.

Example: When decreasing the sound volume of LINE4

43[H] 4C[H] 56[H] 2D[H] 37[H] 0D[H] (‘C L V - 7 CR’)

– 8 –