Sound Modes

Switching ANALOG/DIGITAL Signal Input

When you select a function (for example CD) that is only hooked up by a digital connection, then the ANALOG/DIGITAL signal input switch will automatically choose digital for VSX-D810S/D850S. If you have that function hooked up by both digital and analog connections this switch lets you choose which to listen to.

SOURCE			RECEIVER
DVD		TV	VCR	CD-R
		MULTI CONTROL
RCV		CD	TUN	TVC
1		2		3
MIDNIGHT		5.1 / 7.1		ATT
4		5		6
			EFFECT
7		8		9
10				DISC
		0		ENTER
DTV INFO	MPX/RETURN		D.ACCESS	GUIDE
¶		7	3	8
BAND		CLASS	DTV ON/OFF DTV MENU
1		¡	4	¢	1
2/DTS		DSP	TEST TONE	SIGNAL SELECT	1
CH SELECT		CH LEVEL		FUNCTION
LOUDNESS	FL DIMMER		SETUP	MUTING

1Press SIGNAL SELECT to select the input signal corresponding to the source component.

Each press switches between ANALOG and DIGITAL signal selection (VSX-D710S).

On the VSX-D810S & VSX-D850S receivers there is an AUTO setting. In this setting the receiver will automatically switch between the analog and digital signals according to what is being input. If both signals are input the AUTO setting will choose the digital one. This setting is convenient as the receiver will always choose the best or appropriate signal.

Playing Sources with Dolby Digital or DTS Sound

	SOURCE			RECEIVER		2
	DVD		TV	VCR	CD-R	3
			MULTI CONTROL			3
	RCV		CD	TUN	TVC
	1		2		3
	MIDNIGHT		5.1 / 7.1		ATT
	4		5		6
				EFFECT
	7		8		9
	10				DISC
			0	ENTER
	DTV INFO	MPX/RETURN		D.ACCESS	GUIDE
	¶		7	3	8
	BAND		CLASS	DTV ON/OFF	DTV MENU
	1		¡	4	¢	4
5	2/DTS		DSP	TEST TONE	SIGNAL SELECT
5	CH SELECT		CH LEVEL		FUNCTION
	LOUDNESS	FL DIMMER		SETUP	MUTING
			TUNE
	ST				ST
			ENTER
			TUNE
			CHANNEL
	VOLUME			MASTER VOLUME
			MENU			7
			TV			7
			TVFUNC

TV CONTROL

1Turn on the power of the playback component.

2Turn on the power of the receiver.

Be sure that the standby indicator turns off on the front panel.

3Press MULTI CONTROL buttons or the FUNCTION button to select the source you want to playback.

If the DIRECT FUNCTION is OFF you have to use the FUNCTION button to select the source (see p.39).

2While SIGNAL SELECT is set to DIGITAL, 2DIGITAL lights when a Dolby Digital signal is input, DTS lights when a DTS signal is input.

MEMO:

•SIGNAL SELECT is fixed in the “ANALOG” position for components not assigned to one of the digital input jacks.

•This receiver can only play back Dolby Digital, PCM (32kHz, 44kHz, and 48kHz [VSX-D810S & VSX- D850S can play 96kHz]), and DTS, digital signal formats. With digital signal formats other than these, set SIGNAL SELECT to “ANALOG”.

•Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.

4Press SIGNAL SELECT to select DIGITAL.

(Refer to “Switching ANALOG/DIGITAL signal input” on this page.)

5Press 2/DTS to switch the Dolby/DTS mode on.

6Start playback of the component you selected in step 1.

7Press MASTER VOLUME (+/–) to adjust the volume level.

MEMO:

•You can only hear the sound on DTS encoded discs if the CD or LD player with DTS is digitally connected to this receiver. If you play a DTS encoded disc

through analog connections you will only hear digital
noise, not the soundtrack. To prevent noise, you need
to make digital connections (Refer to page 6-7) and
set SIGNAL SELECT to “DIGITAL”.	29