![](/images/new-backgrounds/1002784/278475x1.webp)
Controlling the Rest of Your System
Learning Mode: Programming Signals from other Remote Controls
If preset codes are not available for your component(s), or the available preset codes do not operate correctly, you can use this function to program in signals from the remote control(s) of your other component(s). This operation can also be used after recalling a preset code to program additional operations not covered in the preset codes.
SOURCE | RECEIVER | ||||
4 D810S only | |||||
LED |
|
|
| ||
DVD | TV | VCR | 3 | ||
| MULTI CONTROL |
| |||
RCV | CD | TUN | TVC |
| |
1 | 2 |
| 3 |
| |
MIDNIGHT | 5.1 / 7.1 | ATT |
| ||
4 | 5 |
| 6 |
| |
|
| EFFECT |
|
| |
7 | 8 |
| 9 |
| |
10 |
|
| DISC |
| |
| 0 |
| ENTER |
| |
DTV INFO MPX/RETURN | D.ACCESS | GUIDE |
| ||
¶ | 7 | 3 | 8 |
| |
BAND | CLASS | DTV ON/OFF DTV MENU |
| ||
1 | ¡ | 4 | ¢ |
| |
2/DTS | DSP | TEST TONE | SIGNAL SELECT |
| |
CH SELECT | CH LEVEL | FUNCTION |
|
LOUDNESS FL DIMMER SETUP | MUTING | 1,7 |
TUNE
ST |
| ST | 2 |
| ENTER |
|
TUNE
VSX-D850S only
CHANNEL
VOLUME | MASTER VOLUME |
MENU
TVFUNC
TV
TV CONTROL
AV
REMOTE CONTROL UNIT
1Press SETUP and hold for three seconds.
The LED on the remote control will light for two seconds.
To cancel the Learning mode at any time Press SETUP.
The remote control will also return to the previous mode after thirty seconds of inactivity.
2
The Learning mode is indicated by the Learning icon (LEARN) in the remote’s LCD display.
3Press the MULTI CONTROL button for the component you want to control
4 button for two seconds to start the Learning mode.
The LED lights steadily.
To cancel LEARNING setup mode
Press SETUP for one second.
If no commands are entered within thirty seconds the
38remote will revert to its previous mode.
En
5Point the two remote controls towards each other. Press the button to be learned on this receiver’s remote control (for example the 3
[play] button).
1 - 2 inches | 3 | 6 | 9 | 8 | ¢ |
|
|
|
| 3 | 4 |
| 2 | 5 | 8 | 0 |
|
|
|
|
| 7 | ¡ |
| 1 | 4 | 7 |
| 1 |
|
|
|
| ¶ |
Point the remote controls directly at each other, about
6Press the corresponding button on the other remote control to be taught to this receiver’s remote control (in the above example the 3
[play] button).
Point the remote controls toward each other. Press the button on the other remote control corresponding to the operation you wish to program. The LED on this receiver’s remote will go out and then resume a steady light if the operation is learned. (For
If this happens press the teaching key repeatedly, varying the distances between the remotes, until you see the LED on this unit’s remote light steadily, without blinking first.
To program additional operations for the current component
Repeat steps 5 and 6.
To program operations for another component Repeat steps 2 through 6
Repeat steps 3 through 6
7Press and hold SETUP for one second to exit the LEARNING setup mode.
After thirty seconds of inactivity the remote control will automatically leave the LEARNING mode and revert to its previous mode.
MEMO:
•Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
•Certain buttons represent modes that cannot be learned from other remote controls. These include:
RCV, CH SELECT, CH LEVEL, FUNCTION LOUDNESS, FL DIMMER, and MUTING.
• TV CONTROL buttons ( TV , VOL