Pioneer VSX-1016V-S, VSX-1016V-K manual Operating Environment

Page 3
D3-4-2-1-7c_A_En
K041_En
D3-4-2-2-1a_A_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

Operating Environment

Operating environment temperature and humidity:

+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a_A_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

Image 3 Pioneer VSX-1016V-S, VSX-1016V-K manual Operating Environment
Contents VSX-1016V-SVSX-1016V-K Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Before you start Installing the receiverIntroduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterSpeaker configuration in the OSD Minute guideWait for the test tones to finish then confirm Playing a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter VSX-1016V Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box DVD playerDVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionConnecting digital audio sources Use a three-way component video cableCD-R, MD, DAT, etc Tape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsTHX speaker system setup Connecting antennasConnecting external antennas Plug the power cord into a power outletPlugging in the receiver Controls and displays Controls and displays ChapterFront panel Controls and displays Operating range of remote control unitSleep Controls and displays DisplayOver / ATT Video ConvSelect Controls and displays Remote controlReceiver Input SelectMute Multi OPEShift SourceStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect optionsUse the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening in stereo Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsBasic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout WMA USB playbackOther compatibility information About MPEG-4 AACListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAn introduction to RDS Using the tunerNaming station presets Listening to station presetsUsing EON Displaying RDS informationPress Disp for RDS information Surround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuFine Channel Level System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuAcoustic Calibration EQ System Setup menuSetting the Acoustic Calibration EQ automatically Fine Speaker DistanceCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Manual speaker setup Speaker SettingChecking your Acoustic Calibration EQ settings Channel Level Select ‘Channel Level’ from the Manual SP Setup menuSelect a setup option Confirm your selected setup optionAdjust the distance of each speaker using THX Audio SettingSelect ‘THX Audio Setting’ from the Manual SP Setup menu Select ‘Speaker Distance’ from the Manual SP Setup menuTHX Speaker Setup Select ‘THX Speaker Setup’ from the Manual SP Setup menuSpecify whether or not you are using a THX speaker system About Hdmi Connecting using HdmiOther connections Other connections ChapterOther connections Second Zone speaker B setupConnecting the multichannel analog inputs Switching the speaker systemConnect your speakers as shown below Bi-wiring your speakersConnecting additional amplifiers Bi-amping your front speakersUsing this receiver with a Pioneer plasma display If you have a Pioneer plasma display, you can use anLarge Audio Using the SR+ mode with a Pioneer plasma displayDVD player DVD/LDAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuDual Mono Setup Other SettingsOther Setup menu Dynamic Range Control SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVideo Converter Setup Making an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signalDisplay shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedanceControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct functionUsing System off Using multi operationsControls for other components Controlling the rest of your system Controls for TVsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorAdditional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsDisplay Remote controlHdmi USB interfaceAdditional information Surround sound formats DolbyWindows Media Audio 9 Professional About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Multichannel signal formatsCleaning the unit Additional information SpecificationsAdditional information Additional information Pioneer Corporation