Pioneer VSX-1016V-K, VSX-1016V-S manual USB interface, Hdmi

Page 64

13Additional information

USB interface

SymptomRemedy

USB mass storage device is not recognized by the receiver.

•Try switching the receiver off, then on again.

•Make sure you have completely inserted the USB connector to this receiver.

•Check that the memory format is FAT16 or FAT32 (FAT12, NTFS and HFS are not supported).

•USB devices with an internal USB hub are not supported.

USB ERR3 shows in the display	• If this message continues to appear after going through all the checks in Important on page 31 of USB
when connecting a USB device.	playback, take the unit to your nearest Pioneer authorized service center or your dealer for servicing.

Can’t play audio files.	• The WMA or MPEG-4 AAC files were recorded using DRM (digital rights management), or the bit rate/
	sampling rate is not compatible (see Compressed audio compatibility on page 31). This is not a
	malfunction.

HDMI

Symptom	Remedy
No picture or sound.	• If the problem still persists when connecting your HDMI component directly to your monitor, please
	consult the component or monitor manual or contact the manufacturer for support.

No picture.	• Depending in the output settings of the source component, it may be outputting a video format that can’t
	be displayed. Change the output settings of the source, or connect using the component, S-video or
	composite jacks.

OSD does not appear.	• The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-
	video, or composite connections when setting up the system.

No sound, or sound suddenly	• Since the HDMI audio signal is sent through this receiver to your TV, you need to make separate
ceases.	connections for audio if you want to hear your HDMI component through this system. See Connecting using
	HDMI on page 44 for more on this.
	• If you’ve made separate connections for audio, make sure you have assigned the analog/digital jack(s) to
	the corresponding HDMI input for the component. See Assigning the HDMI inputs on page 50 to do this.
	• Check the audio output settings of the source component.

Note

•If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

64

En

Image 64

Contents VSX-1016V-SVSX-1016V-K Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Other Settings Using other functionsOther connections Controlling the rest of your systemFeatures Before you startBefore you start Chapter Checking what’s in the boxBefore you start Installing the receiver Loading the batteriesAutomatically setting up for surround sound Mcacc Minute guide02 5 minute guide Chapter Introduction to home theaterMinute guide Speaker configuration in the OSDWait for the test tones to finish then confirm Better sound using Basic Phase Control Problems when using the Auto Mcacc Setup02 5 minute guide Playing a sourceConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter Connecting your equipment Connecting your TV and DVD player Connecting a satellite/cable receiver or other set-top boxDVD player VSX-1016VConnecting a DVD/HDD recorder, VCR and other video sources Using the component video jacksUse an optical cable for the connection DVR, VCR, etcUse a three-way component video cable Connecting digital audio sourcesCD-R, MD, DAT, etc Connecting analog audio sources Connecting a component to the front panel inputsAbout the WMA9 Pro decoder Tape deck, etcConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupPlug the power cord into a power outlet Connecting external antennasPlugging in the receiver Controls and displays Chapter Controls and displaysFront panel Operating range of remote control unit Controls and displaysControls and displays Display Over / ATTVideo Conv SleepControls and displays Remote control ReceiverInput Select SelectMulti OPE ShiftSource MuteListening to your system Listening to your system ChapterAuto playback Listening in surround sound Standard surround soundUsing the Home THX modes Using the Advanced surround effectsSetting the effect options Listening to your systemPress EFFECT/CH SEL again to adjust other settings Listening in stereoListening with Acoustic Calibration EQ Use the +/- buttons to set it as necessaryListening to your system Choosing the input signal Using the Virtual Surround Back modeUsing Midnight and Loudness Using the Sound RetrieverUsing the tone controls Press Tone to select the frequency you want to adjustUsing the USB interface USB playbackUSB playback Chapter Basic playback controlsUSB playback Other compatibility informationAbout MPEG-4 AAC About WMAUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets An introduction to RDSDisplaying RDS information Using EONPress Disp for RDS information System Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu Fine Channel LevelSystem Setup menu Setting the Acoustic Calibration EQ automaticallyFine Speaker Distance Acoustic Calibration EQSetting the Acoustic Calibration EQ manually Copying your Acoustic Calibration EQ settingsFront Align Speaker Setting Manual speaker setupChecking your Acoustic Calibration EQ settings Select ‘Channel Level’ from the Manual SP Setup menu Select a setup optionConfirm your selected setup option Channel LevelTHX Audio Setting Select ‘THX Audio Setting’ from the Manual SP Setup menuSelect ‘Speaker Distance’ from the Manual SP Setup menu Adjust the distance of each speaker usingSelect ‘THX Speaker Setup’ from the Manual SP Setup menu THX Speaker SetupSpecify whether or not you are using a THX speaker system Connecting using Hdmi Other connectionsOther connections Chapter About HdmiSecond Zone speaker B setup Connecting the multichannel analog inputsSwitching the speaker system Other connectionsBi-wiring your speakers Connecting additional amplifiersBi-amping your front speakers Connect your speakers as shown belowIf you have a Pioneer plasma display, you can use an Using this receiver with a Pioneer plasma displayLarge Using the SR+ mode with a Pioneer plasma display DVD playerDVD/LD AudioOther Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other Setup menuDynamic Range Control Setup Dual Mono SetupSR+ Setup for Pioneer plasma displays LFE Attenuator SetupVideo Converter Setup Using other functions Using other functions ChapterReducing the level of an analog signal Making an audio or a video recordingUsing other functions Using the sleep timer Resetting the systemSwitching the speaker impedance Display shows RESET?Setting the remote to control other components Selecting preset codes directlyProgramming signals from other remote controls Controlling the rest of your systemErasing one of the remote control button settings Resetting the remote control presetsConfirming preset codes Controlling the rest of your systemRenaming input source names Multi Operation and System OffDirect function Programming a multi-operation or a shutdown sequenceUsing multi operations Using System offControlling the rest of your system Controls for TVs Controls for other componentsOperating other Pioneer components with this unit’s sensor Decide which component you want to use the remote sensorTroubleshooting PowerAdditional information Additional information ChapterOther audio problems Additional informationSettings VideoRemote control DisplayUSB interface HdmiDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THX Listening modes with different input signal formats Stereo 2 channel signal formatsTHX Games Mode THX MusicModeMultichannel signal formats AutoAdditional information Specifications Cleaning the unitAdditional information Additional information Pioneer Corporation