Pioneer VSX-1016V-K, VSX-1016V-S manual Placing the speakers, Bare wire connections

Page 18

03Connecting your equipment

Bare wire connections

Make sure that the speaker cable you’re going to use is properly prepared with about 10 mm of insulator stripped from each wire, and the exposed wire strands twisted together (fig. A).

To connect a terminal, unscrew the terminal a few turns until there is enough space to insert the exposed wire (fig. B). Once the wire is in position, tighten the terminal until the wire is firmly clamped (fig. C).

fig. A

fig. B

fig. C

10 mm

Important

Please refer to the manual that came with your speakers for details on how to connect the other end of the speaker cables to your speakers.

Other connections on page 44 provides greater detail on alternate speaker setups, such as using speaker system B (page 45), bi-amping (page 46) and bi- wiring (page 46).

If you are using a THX certified subwoofer use the THX INPUT jack on the subwoofer (if your subwoofer has one) or switch the filter position to THX on your subwoofer.

Placing the speakers

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.

The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.

For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from the TV.

When placing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference, such as discoloration of the picture when the TV is switched on. If you do not have magnetically shielded speakers and notice discoloration of the TV picture, move the speakers farther away from the TV.

If you're using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower angle.

Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.

It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.

Surround and surround back speakers should be positioned 60 cm to 90 cm higher than your ears and titled slight downward. Make sure the speakers don't face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.

Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

Front

Center

Front

left

right

 

 

Subwoofer

Surround

 

Surround

left

 

right

Listening position

Surround back left

 

Surround back right

Single surround back speaker

Caution

Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.

18

En

Image 18
Contents VSX-1016V-SVSX-1016V-K Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Other connections Other SettingsUsing other functions Controlling the rest of your systemBefore you start Chapter FeaturesBefore you start Checking what’s in the boxBefore you start Installing the receiver Loading the batteries02 5 minute guide Chapter Automatically setting up for surround sound McaccMinute guide Introduction to home theaterSpeaker configuration in the OSD Minute guideWait for the test tones to finish then confirm 02 5 minute guide Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup Playing a sourceConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter DVD player Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box VSX-1016VUse an optical cable for the connection Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks DVR, VCR, etcConnecting digital audio sources Use a three-way component video cableCD-R, MD, DAT, etc About the WMA9 Pro decoder Connecting analog audio sourcesConnecting a component to the front panel inputs Tape deck, etcConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupConnecting external antennas Plug the power cord into a power outletPlugging in the receiver Controls and displays Controls and displays ChapterFront panel Operating range of remote control unit Controls and displaysVideo Conv Controls and displays DisplayOver / ATT SleepInput Select Controls and displays Remote controlReceiver SelectSource Multi OPEShift MuteAuto playback Listening in surround sound Listening to your systemListening to your system Chapter Standard surround soundSetting the effect options Using the Home THX modesUsing the Advanced surround effects Listening to your systemListening with Acoustic Calibration EQ Press EFFECT/CH SEL again to adjust other settingsListening in stereo Use the +/- buttons to set it as necessaryListening to your system Choosing the input signal Using the Virtual Surround Back modeUsing the tone controls Using Midnight and LoudnessUsing the Sound Retriever Press Tone to select the frequency you want to adjustUSB playback Chapter Using the USB interfaceUSB playback Basic playback controlsAbout MPEG-4 AAC USB playbackOther compatibility information About WMASaving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets An introduction to RDSUsing EON Displaying RDS informationPress Disp for RDS information Making receiver settings from the System Setup menu System Setup menuSystem Setup menu Chapter Surround back speaker settingSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Fine Channel LevelFine Speaker Distance System Setup menuSetting the Acoustic Calibration EQ automatically Acoustic Calibration EQCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Manual speaker setup Speaker SettingChecking your Acoustic Calibration EQ settings Confirm your selected setup option Select ‘Channel Level’ from the Manual SP Setup menuSelect a setup option Channel LevelSelect ‘Speaker Distance’ from the Manual SP Setup menu THX Audio SettingSelect ‘THX Audio Setting’ from the Manual SP Setup menu Adjust the distance of each speaker usingTHX Speaker Setup Select ‘THX Speaker Setup’ from the Manual SP Setup menuSpecify whether or not you are using a THX speaker system Other connections Chapter Connecting using HdmiOther connections About HdmiSwitching the speaker system Second Zone speaker B setupConnecting the multichannel analog inputs Other connectionsBi-amping your front speakers Bi-wiring your speakersConnecting additional amplifiers Connect your speakers as shown belowUsing this receiver with a Pioneer plasma display If you have a Pioneer plasma display, you can use anLarge DVD/LD Using the SR+ mode with a Pioneer plasma displayDVD player AudioInput Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsDynamic Range Control Setup Other SettingsOther Setup menu Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVideo Converter Setup Reducing the level of an analog signal Using other functionsUsing other functions Chapter Making an audio or a video recordingSwitching the speaker impedance Using other functions Using the sleep timerResetting the system Display shows RESET?Programming signals from other remote controls Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemConfirming preset codes Erasing one of the remote control button settingsResetting the remote control presets Controlling the rest of your systemDirect function Renaming input source namesMulti Operation and System Off Programming a multi-operation or a shutdown sequenceUsing multi operations Using System offControlling the rest of your system Controls for TVs Controls for other componentsOperating other Pioneer components with this unit’s sensor Decide which component you want to use the remote sensorAdditional information TroubleshootingPower Additional information ChapterOther audio problems Additional informationSettings VideoRemote control DisplayUSB interface HdmiAdditional information Surround sound formats DolbyWindows Media Audio 9 Professional About THX THX Games Mode Listening modes with different input signal formatsStereo 2 channel signal formats THX MusicModeMultichannel signal formats AutoAdditional information Specifications Cleaning the unitAdditional information Additional information Pioneer Corporation