Pioneer VSX-1016V-S, VSX-1016V-K manual Display, Remote control

Page 63

Additional information

13

Display

Symptom	Remedy
The display is dark or off.	• Press DIMMER on the remote control repeatedly to select a different brightness.

After making an adjustment the	• Press DIMMER on the remote control repeatedly to select a different brightness.
display goes off.

You can't get DIGITAL to display	• Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input
when using the SIGNAL SELECT	Assign menu on page 49).
button.	• If the multichannel analog inputs are selected, select a different input source.

The Dolby/DTS indicator doesn't	• These indicators do dot light if playback is paused.
light when playing Dolby/DTS	• Check the playback (especially the digital output) settings of the source component.
software.

When playing a DVD-Audio disc,	• This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog outputs of
the DVD player display shows	the DVD player. This receiver cannot show the playback sample rate when using the analog inputs.
96 kHz. However, the receiver’s
display does not.

During playback of a DTS 96/24	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 29).
source, the display doesn't show
96 kHz.

When playing Dolby Digital or	• Check that the player is connected using a digital connection.
DTS sources, the receiver’s	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 29).
format indicators do not light.	• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.
	• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.

When playing certain discs, none	• The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what audio
of the receiver’s format	tracks are recorded on the disc.
indicators light.

When playing a disc, the	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 29).
2 PL II or Neo:6 indicator lights	• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is not a
on the receiver.	malfunction. Check the disc packaging for details about the audio tracks available.

During playback of a Surround	• The source may be Dolby Surround EX / DTS ES software, but it has no flag to indicate it is 6.1
EX or DTS ES source on the SBch	compatible. Set to SBch ON (see Using surround back channel processing on page 29) then switch to the
AUTO setting, the EX and ES	THX Surround EX or Standard EX listening mode (see Listening in surround sound on page 26).
indicators don’t light, or the
signal is not properly processed.

Remote control

Symptom	Remedy
Cannot be remote controlled.	• Try replacing the batteries in the remote control (see Loading the batteries on page 7).
	• Be sure to operate within 7 meters and a 30º angle of the remote sensor on the front panel (see Operating
	range of remote control unit on page 22).
	• Check that there are no obstacles between the receiver and the remote control.
	• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
	• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this unit’s
	sensor on page 59).

Other components can't be	• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
operated with the system remote.	• The preset code may be incorrect. Redo the procedure for entering preset codes.

The SR cable is connected, but	• Reinsert the SR cable, making sure it’s connected to the right jack (see Using this receiver with a Pioneer
the connected components can’t	plasma display on page 47).
be operated with the remote.	• Make sure that there is an analog connection between the units. This is necessary for the SR feature to
	work.
	• Check that the other component is made by Pioneer. The SR feature only works with Pioneer equipment.

63

En

Image 63

Contents VSX-1016V-SVSX-1016V-K Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Before you start Installing the receiverIntroduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterSpeaker configuration in the OSD Minute guideWait for the test tones to finish then confirm Playing a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter VSX-1016V Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box DVD playerDVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionConnecting digital audio sources Use a three-way component video cableCD-R, MD, DAT, etc Tape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsTHX speaker system setup Connecting antennasConnecting external antennas Plug the power cord into a power outletPlugging in the receiver Controls and displays Controls and displays ChapterFront panel Controls and displays Operating range of remote control unitSleep Controls and displays DisplayOver / ATT Video ConvSelect Controls and displays Remote controlReceiver Input SelectMute Multi OPEShift SourceStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect optionsUse the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening in stereo Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsBasic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout WMA USB playbackOther compatibility information About MPEG-4 AACListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAn introduction to RDS Using the tunerNaming station presets Listening to station presetsUsing EON Displaying RDS informationPress Disp for RDS information Surround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuFine Channel Level System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuAcoustic Calibration EQ System Setup menuSetting the Acoustic Calibration EQ automatically Fine Speaker DistanceCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Manual speaker setup Speaker SettingChecking your Acoustic Calibration EQ settings Channel Level Select ‘Channel Level’ from the Manual SP Setup menuSelect a setup option Confirm your selected setup optionAdjust the distance of each speaker using THX Audio SettingSelect ‘THX Audio Setting’ from the Manual SP Setup menu Select ‘Speaker Distance’ from the Manual SP Setup menuTHX Speaker Setup Select ‘THX Speaker Setup’ from the Manual SP Setup menuSpecify whether or not you are using a THX speaker system About Hdmi Connecting using HdmiOther connections Other connections ChapterOther connections Second Zone speaker B setupConnecting the multichannel analog inputs Switching the speaker systemConnect your speakers as shown below Bi-wiring your speakersConnecting additional amplifiers Bi-amping your front speakersUsing this receiver with a Pioneer plasma display If you have a Pioneer plasma display, you can use anLarge Audio Using the SR+ mode with a Pioneer plasma displayDVD player DVD/LDAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuDual Mono Setup Other SettingsOther Setup menu Dynamic Range Control SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVideo Converter Setup Making an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signalDisplay shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedanceControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct functionUsing System off Using multi operationsControls for other components Controlling the rest of your system Controls for TVsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorAdditional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsDisplay Remote controlHdmi USB interfaceAdditional information Surround sound formats DolbyWindows Media Audio 9 Professional About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Multichannel signal formatsCleaning the unit Additional information SpecificationsAdditional information Additional information Pioneer Corporation