Harman 1210KA manual Overview, SECOND Guide EFX

Page 10

OVERVIEW

To get you working as fast as possible, this manual begins with a 60-second guide. Here you can find quick information on any feature of the EFX console.

BANK A

KARAOKE

THE 60-SECOND GUIDE - EFX

1

MIC INPUT (XLR)

Connect Microphones here. If you are using a condenser mic, ensure phantom

 

 

power is supplied by pressing the switch at the top of the master section.

 

 

WARNING: Do Not apply Phantom Power before connecting a

 

LINE INPUT (¼” Jack)

microphone.

2

Connect Line level sources here, e.g. Synth, Drum Machine, DI etc.

3

INSERT POINT (¼” Jack)

Connect Signal processors here, e.g. Compressor, Gate etc.

4 GAIN CONTROL

Adjust this to increase or decrease the level of the incoming signal.

5

EQ STAGE

Adjust these controls to change the signal tone (the character of the signal).

6 AUX 1 SEND

Adjust this control to change the level of the signal to an artist’s monitors

 

 

(headphones/in-ear/stage monitors). Aux 1 is globally switchable pre/post

 

 

fade.

7

FX SEND

This control sets the level of the post-fade signal being sent to the FX bus;

 

 

from there it is routed to the FX processor.

8 PAN CONTROL

Use this control to position the signal within the stereo field.

9 MUTE SWITCH

When this is pressed you will hear no signal from the channel (post-mute

 

 

signals).

10 PFL

When pressed the signal will appear on the monitor and headphone outputs

 

 

- use this to monitor the post-EQ signal from the channel.

 

 

 

8

 

Soundcraft EFX/EPM User Guide Issue 1210

Image 10
Contents User Guide Soundcraft EFX/EPM User Guide Issue User Guide EPM Models Contents Safety Symbol Guide Important Safety Instructions Neutral Blue US White Live Hot Brown US Black Advice for Those WHO Push the Boundaries IntroductionOverview 60-SECOND Guide EFXMaster Faders Phantom PowerPeak LED Main MetersAUX 1/2 Sends 60-SECOND Guide EPMPFL 22 2-TRACK Inputs Mono OUT ¼ Jack23 2-TRACK Controls Line Input Wiring UPMic Input Insert PointMix Outputs Stereo Inputs Stereo 1/2 and StereoMix Inserts Aux & FX Bus OutputsPolarity Phase HeadphonesGrounding and Shielding Products Under Warranty OUT-OF-WARRANTY Products Problem SolvingIf in doubt please contact Soundcraft customer support Block Diagram Soundcraft EFX Block Diagram Soundcraft EPM Mono Input Channel EFX shown GainMID EQ HF EQLF EQ Mute Aux 2 Send EPM onlyPAN Input Channel FaderGain Gain control sets the level of the channel signalInputs Stereo 1/2 MF EQFader BalanceChannel Peak LED Soundcraft EFX/EPM User Guide Issue MIX OUTPUTS, Inserts & Mono Output Power IndicatorMaster Section EFX Bargraph MetersTrack Headphones JackAUX 1 PRE/POST Switch and AUX 2 on EPM Track to MIXStereo Return Inputs EFX only Footswitch EFX onlyFX BUS Output EFX only Aux 2 on EPM Stereo Return Level EFX onlySelect and Load a Program FX OperationSet Audio Levels FX Processor Controls EFX only Reverbs Reverb Controls KaraokeDelays Delay Controls Modulated EffectsTremelo/Pan PhaserFlanger VibratoFactory Reset Effects Data Chart EFX only Microphone Placement Using Your EFX or EPM ConsoleInitial Setup Page Applications Application 3 Places of Worship using EFX Application 4 Recording Soundcraft EFX/EPM User Guide Issue Glossary Peaking Distort the signalPhase BandTypical Connecting Leads Soundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Karaoke MARK-UP Sheets EPM Soundcraft EFX/EPM User Guide Issue Fitting Optional Rackmount Ears Part numbers for the kits areSoundcraft EFX/EPM User Guide Issue EPM/EFX Typical Specifications Soundcraft EFX/EPM User Guide Issue Warranty Benefit of this Warranty may not be assigned by the End UserSoundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Page Soundcraft Soundcraft USA Balboa Boulevard