Harman 1210KA Inputs Stereo 1/2, Gain control sets the level of the channel signal, Mf Eq

Page 23

STEREO INPUT CHANNELS (EFX shown)

1 INPUTS STEREO 1/2

These inputs accept 3-pole ‘A’ gauge (TRS) jacks. Use these inputs for sources such as keyboards, drum machines, synths, tape machines or processing units. The inputs are BALANCED for low noise and top quality from professional equipment, but you can use UNBALANCED sources by wiring up the jacks as shown in the “Wiring it Up” section earlier in this manual, although you should then keep cable lengths as short as possible. Mono sources may be used by plugging into the left jack only.

2 GAIN

The GAIN control sets the level of the channel signal.

3EQUALISER HF EQ

Turn to the right to boost high (treble) frequencies, adding crispness to percussion from drum machines, synths and electronic instruments. Turn to the left to cut these frequencies, reducing hiss or excessive brilliance. Set the knob in the centre-detented position when not required. The control has a shelving response giving 15dB of boost or cut at 12kHz.

MF EQ

Turn to the right to boost mid frequencies, turn to the left to cut these frequencies. The centre frquency of the MID EQ is 720Hz

LF EQ

Turn to the right to boost low (bass) frequencies, adding extra punch to synths, guitars and drums. Turn to the left to reduce hum, boominess or improve a mushy sound. Set the knob to the centre-detented position when not required. The control has a shelving response giving 15dB of boost or cut at 80Hz.

4AUX 1 SEND

This is used to set up a separate mix for FOLDBACK or recording, and the combination of each Aux Send is mixed to the Aux1 Output. For recording it is useful for the signal to fade up and down with the fader (this is called POST-FADE), but for Foldback or Monitor feeds it is important for the send to be independent of the fader (this is called PRE-FADE).

AUX 1 SEND is globally switchable between pre and post-fade (see master section on page 24/25). The send pot is fed with a mono sum of the L & R signals.

5 FX SEND (EFX only)

This control sets the level of the post-fade signal being sent to the FX bus; from there it is routed to the FX processor.

Soundcraft EFX/EPM User Guide Issue 1210

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents User Guide Soundcraft EFX/EPM User Guide Issue User Guide EPM Models Contents Safety Symbol Guide Important Safety Instructions Neutral Blue US White Live Hot Brown US Black Introduction Advice for Those WHO Push the Boundaries60-SECOND Guide EFX OverviewMain Meters Phantom PowerPeak LED Master FadersPFL 60-SECOND Guide EPMAUX 1/2 Sends 23 2-TRACK Controls Mono OUT ¼ Jack22 2-TRACK Inputs Insert Point Wiring UPMic Input Line InputAux & FX Bus Outputs Stereo Inputs Stereo 1/2 and StereoMix Inserts Mix OutputsGrounding and Shielding HeadphonesPolarity Phase If in doubt please contact Soundcraft customer support Problem SolvingProducts Under Warranty OUT-OF-WARRANTY Products Block Diagram Soundcraft EFX Block Diagram Soundcraft EPM Gain Mono Input Channel EFX shownLF EQ HF EQMID EQ Input Channel Fader Aux 2 Send EPM onlyPAN MuteMF EQ Gain control sets the level of the channel signalInputs Stereo 1/2 GainChannel Peak LED BalanceFader Soundcraft EFX/EPM User Guide Issue Bargraph Meters Power IndicatorMaster Section EFX MIX OUTPUTS, Inserts & Mono OutputTrack to MIX Headphones JackAUX 1 PRE/POST Switch and AUX 2 on EPM TrackStereo Return Level EFX only Footswitch EFX onlyFX BUS Output EFX only Aux 2 on EPM Stereo Return Inputs EFX onlySet Audio Levels FX OperationSelect and Load a Program FX Processor Controls EFX only Reverbs Karaoke Reverb ControlsDelays Modulated Effects Delay ControlsVibrato PhaserFlanger Tremelo/PanFactory Reset Effects Data Chart EFX only Initial Setup Using Your EFX or EPM ConsoleMicrophone Placement Page Applications Application 3 Places of Worship using EFX Application 4 Recording Soundcraft EFX/EPM User Guide Issue Glossary Band Distort the signalPhase PeakingTypical Connecting Leads Soundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Karaoke MARK-UP Sheets EPM Soundcraft EFX/EPM User Guide Issue Part numbers for the kits are Fitting Optional Rackmount EarsSoundcraft EFX/EPM User Guide Issue EPM/EFX Typical Specifications Soundcraft EFX/EPM User Guide Issue Benefit of this Warranty may not be assigned by the End User WarrantySoundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Page Balboa Boulevard Soundcraft Soundcraft USA
Top Page Image Contents