Harman 1210KA manual SECOND Guide EPM, AUX 1/2 Sends, Pfl

Page 12

THE 60-SECOND GUIDE - EPM

1 MIC INPUT (XLR)		Connect Microphones here. If you are using a condenser mic, ensure phantom
		power is supplied by pressing the switch at the top of the master section.
		WARNING: Do Not apply Phantom Power before connecting
	LINE INPUT (¼” Jack)	a microphone.
2	LINE INPUT (¼” Jack)	Connect Line level sources here, e.g. Synth, Drum Machine, DI etc.
3	INSERT POINT (¼” Jack)	Connect Signal processors here, e.g. Compressor, Gate etc.
4 GAIN CONTROL		Adjust this to increase or decrease the level of the incoming signal.
5	EQ STAGE	Adjust these controls to change the signal tone (the character of the signal).
6 AUX 1/2 SENDS		Adjust these controls to change the level of the signal to an artist’s monitors
		(headphones/in-ear/stage monitors). Each Aux is globally switchable pre/
		post fade.
7 PAN CONTROL		Use this control to position the signal within the stereo field.
8 MUTE SWITCH		When this is pressed you will hear no signal from the channel (post-mute
		signals).
9	PFL	When pressed the signal will appear on the monitor and headphone outputs
		- use this to monitor the post-EQ signal from the channel.

10	Soundcraft EFX/EPM User Guide Issue 1210

Image 12

Contents User Guide Soundcraft EFX/EPM User Guide Issue User Guide EPM Models Contents Safety Symbol Guide Important Safety Instructions Neutral Blue US White Live Hot Brown US Black Advice for Those WHO Push the Boundaries IntroductionOverview 60-SECOND Guide EFXPhantom Power Peak LEDMaster Faders Main Meters60-SECOND Guide EPM AUX 1/2 SendsPFL Mono OUT ¼ Jack 22 2-TRACK Inputs23 2-TRACK Controls Wiring UP Mic InputLine Input Insert PointStereo Inputs Stereo 1/2 and Stereo Mix InsertsMix Outputs Aux & FX Bus OutputsHeadphones Polarity PhaseGrounding and Shielding Problem Solving Products Under Warranty OUT-OF-WARRANTY ProductsIf in doubt please contact Soundcraft customer support Block Diagram Soundcraft EFX Block Diagram Soundcraft EPM Mono Input Channel EFX shown GainHF EQ MID EQLF EQ Aux 2 Send EPM only PANMute Input Channel FaderGain control sets the level of the channel signal Inputs Stereo 1/2Gain MF EQBalance FaderChannel Peak LED Soundcraft EFX/EPM User Guide Issue Power Indicator Master Section EFXMIX OUTPUTS, Inserts & Mono Output Bargraph MetersHeadphones Jack AUX 1 PRE/POST Switch and AUX 2 on EPMTrack Track to MIXFootswitch EFX only FX BUS Output EFX only Aux 2 on EPMStereo Return Inputs EFX only Stereo Return Level EFX onlyFX Operation Select and Load a ProgramSet Audio Levels FX Processor Controls EFX only Reverbs Reverb Controls KaraokeDelays Delay Controls Modulated EffectsPhaser FlangerTremelo/Pan VibratoFactory Reset Effects Data Chart EFX only Using Your EFX or EPM Console Microphone PlacementInitial Setup Page Applications Application 3 Places of Worship using EFX Application 4 Recording Soundcraft EFX/EPM User Guide Issue Glossary Distort the signal PhasePeaking BandTypical Connecting Leads Soundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Karaoke MARK-UP Sheets EPM Soundcraft EFX/EPM User Guide Issue Fitting Optional Rackmount Ears Part numbers for the kits areSoundcraft EFX/EPM User Guide Issue EPM/EFX Typical Specifications Soundcraft EFX/EPM User Guide Issue Warranty Benefit of this Warranty may not be assigned by the End UserSoundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Page Soundcraft Soundcraft USA Balboa Boulevard