Harman 1210KA manual FX Operation, Select and Load a Program, Set Audio Levels

Page 29

Lexicon® FX PROCESSOR OVERVIEW (EFX only)

The effects within the console have been designed with both live sound reinforcement and home recording in mind. Featuring the deep, rich reverb algorithms that Lexicon® are renowned for the effects processor offers increased versatility and high quality effects, all instantly accessible via the extremely intuitive front panel controls. The effects processor has 32 programs which are held in two banks of 16 programs which can be stored to allow you to create your own custom effect settings.

Front panel controls include a Program Select knob, Tempo and Store buttons, and three independent Parameter knobs that provide instant access and control over the most critical parameters for the selected effect. The table on page 35 lists the functions of the parameter knobs for each fx program.

Note: When the console is powered up the program recalled will always be the selected program in BANK A.

FX OPERATION

Select and Load a Program

Turn the Program Select knob to choose a program. Note that the console has 32 programs which are held in two banks of 16 programs. There are individual BANK A and BANK B LED’s to indicate which bank is cur- rently active. When turning the rotary Program Select knob through 360 degrees (a full rotation) the selected bank will alternate between BANK A and BANK B.

Set Audio Levels

1.Set the gain on the input channel appropriate to the source (vocal microphone, guitar, keyboard, etc.).

2.Set the FX send on the input channel to the 12 o’clock position.

3.Set the EFFECTS Fader on the FX section to the fully down position.

4.Provide source signal (by speaking or singing into the microphone, playing guitar, keyboard, etc.) on the selected channel.

5.Turn up the FX Send level on the channel until the Red CLIP LED in the FX Panel lights only occasionally. If the red Input LED stays lit, too much signal is being sent to the effect processor: reduce FX Send on the input channel.

6.Raise the EFFECTS Fader towards the 0dB position to feed the required level of FX Processor output signal to the mix.

7.To increase or decrease the amount of effect on the signal, adjust the FX Send level on the channel that you want affected.

Soundcraft EFX/EPM User Guide Issue 1210

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents User Guide Soundcraft EFX/EPM User Guide Issue User Guide EPM Models Contents Safety Symbol Guide Important Safety Instructions Neutral Blue US White Live Hot Brown US Black Introduction Advice for Those WHO Push the Boundaries60-SECOND Guide EFX OverviewPeak LED Phantom PowerMaster Faders Main MetersPFL 60-SECOND Guide EPMAUX 1/2 Sends 23 2-TRACK Controls Mono OUT ¼ Jack22 2-TRACK Inputs Mic Input Wiring UPLine Input Insert PointMix Inserts Stereo Inputs Stereo 1/2 and StereoMix Outputs Aux & FX Bus OutputsGrounding and Shielding HeadphonesPolarity Phase If in doubt please contact Soundcraft customer support Problem SolvingProducts Under Warranty OUT-OF-WARRANTY Products Block Diagram Soundcraft EFX Block Diagram Soundcraft EPM Gain Mono Input Channel EFX shownLF EQ HF EQMID EQ PAN Aux 2 Send EPM onlyMute Input Channel FaderInputs Stereo 1/2 Gain control sets the level of the channel signalGain MF EQChannel Peak LED BalanceFader Soundcraft EFX/EPM User Guide Issue Master Section EFX Power IndicatorMIX OUTPUTS, Inserts & Mono Output Bargraph MetersAUX 1 PRE/POST Switch and AUX 2 on EPM Headphones JackTrack Track to MIXFX BUS Output EFX only Aux 2 on EPM Footswitch EFX onlyStereo Return Inputs EFX only Stereo Return Level EFX onlySet Audio Levels FX OperationSelect and Load a Program FX Processor Controls EFX only Reverbs Karaoke Reverb ControlsDelays Modulated Effects Delay ControlsFlanger PhaserTremelo/Pan VibratoFactory Reset Effects Data Chart EFX only Initial Setup Using Your EFX or EPM ConsoleMicrophone Placement Page Applications Application 3 Places of Worship using EFX Application 4 Recording Soundcraft EFX/EPM User Guide Issue Glossary Phase Distort the signalPeaking BandTypical Connecting Leads Soundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Karaoke MARK-UP Sheets EPM Soundcraft EFX/EPM User Guide Issue Part numbers for the kits are Fitting Optional Rackmount EarsSoundcraft EFX/EPM User Guide Issue EPM/EFX Typical Specifications Soundcraft EFX/EPM User Guide Issue Benefit of this Warranty may not be assigned by the End User WarrantySoundcraft EFX/EPM User Guide Issue Soundcraft EFX/EPM User Guide Issue Page Balboa Boulevard Soundcraft Soundcraft USA
Top Page Image Contents