Harman MFXI, MPMI manual Lexicon FX Processor Overview, FX Operation, Select and Load a Program

Page 35

Lexicon® FX PROCESSOR OVERVIEW

The effects within the console have been designed with both live sound reinforcement and home recording in mind. Featuring the deep, rich reverb algorithms that Lexicon® are renowned for the effects processor offers increased versatility and high quality effects, all instantly accessible via the extremely intuitive front panel controls. The effects processor has 32 programs which are held in two banks of 16 programs which can be stored to allow you to create your own custom effect settings.

Front panel controls include a Program Select knob, Tempo and Store buttons, and three independent Parameter knobs that provide instant access and control over the most critical parameters for the selected effect. The table on page 40 lists the functions of the Parameter knobs for each fx program.

Note: When the console is powered up the program recalled will always be the selected program in BANK A.

FX OPERATION

Select and Load a Program

Turn the Program Select knob to choose a program. Note that the console has 32 programs which are held in two banks of 16 programs. There are individual BANK A and BANK B LED’s to indicate which bank is cur- rently active. When turning the rotary Program Select knob through 360 degrees (a full rotation) the selected bank will alternate between BANK A and BANK B.

Set Audio Levels

1.Set the gain on the input channel appropriate to the source (vocal microphone, guitar, keyboard, etc.).

2.Set the FX send on the input channel to the 2 o’clock position.

3.Set the FX Master level to the 2 o’clock position. Set the EFFECTS Fader on the FX section to the fully down position.

4.Provide source signal (by speaking or singing into the microphone, playing guitar, keyboard, etc.) on the selected channel.

5.Turn up the FX Send level on the channel until the Red CLIP LED in the FX Panel lights only occasionally. If the red Input LED stays lit, too much signal is being sent to the effect processor; reduce the FX Master or the FX Send on the input channel.

6.Raise the EFFECTS Fader towards the 0dB position to feed the required level of FX Processor output signal to the mix.

7.To increase or decrease the amount of effect on the signal, adjust the FX Send level on the channel that you want affected.

Soundcraft MFXi MPMi User Guide Issue 1210

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents User Guide Page User Guide Potters BAR Contents Important Safety Instructions Neutral Blue US White Live Hot Brown US Black Safety Symbol Guide Soundcraft MFXi MPMi User Guide Issue Consignes DE Sécurité Importantes Vert et Jaune US Vert/Jaune Informations utiles sur l’utilisation de la console Guide DES Symboles DE SécuritéAvertissement RemarquesIntroduction Advice for Those WHO Push the Boundaries60-SECOND Guide MFXi SUB-GROUP Routing MIC 60-SECOND Guide MPMiBe monitored also, see item 30 below Insert Point Wiring UPMic Input Line InputAux and FX Bus Outputs HeadphonesStereo Inputs Stereo 1/2 Mix OutputsCables Polarity PhaseGrounding and Shielding UK customers should contact their local dealer Problem SolvingProducts Under Warranty OUT-OF-WARRANTY ProductsAUX Outputs Block Diagram MFXiMPMi High-pass Filter Mono Input Channels MFXi shownLF EQ HF EQMID EQ Input Channel Fader Signal Present SP LEDPAN MuteMF EQ Stereo Input Channels MFXi shownInputs Stereo 1/2 GainChannel Peak LED BalanceFader PFLSoundcraft MFXi MPMi User Guide Issue Master Section MFXi Master Section MPMi Headphones Socket Power IndicatorPhantom Power Headphones LevelSUB to MIX Meters & Solo LEDMIX Fader SUB FadersFX AFL 23 PRE/POST SwitchMute FX Footswitch FX MasterSet Audio Levels Lexicon FX Processor OverviewFX Operation Select and Load a ProgramFX Processor Controls MFXi only Reverbs Karaoke Reverb ControlsDelays Modulated Effects Delay ControlsTremelo/Pan Factory ResetPhaser FlangerEffects Data Chart Crosstalk @ 1kHz MFXi/MPMi Typical SpecificationsInitial Setup Using Your MFXi/MPMi ConsoleMicrophone Placement Page STE1 STE2 Effects 48V Used forFitting Optional RACK-MOUNT Brackets Mixer DimensionsExtender Applications Instrument and Vocal Sources Configurations can be driven by the MFXiPlayer Application 3 Places of WorshipStudio Control Room Application 4 RecordingTypical Connecting Leads ‘Y’ Cables Unbalanced Glossary See above Pre-fadePosition A highpass or lowpass derived responseBenefit of this Warranty may not be assigned by the End User WarrantySoundcraft MFXi MPMi User Guide Issue Balboa Boulevard Soundcraft Soundcraft USA
Top Page Image Contents