Harman MFXI, MPMI Meters & Solo LED, MIX Fader, SUB Faders, SUB to MIX, Stereo/Mono, MIX Outputs

Page 33

12 METERS & SOLO LED

The three-colour peak reading BARGRAPH METERS normally show the level of the signal(s) selected by the monitor source-select switches, giving you a constant warning of excessive peaks in the signal(s) which might cause overloading. Aim to keep the signal within the amber segments at peak levels for best performance. Similarly, if the output level is too low and hardly registering at all on the meters, the level of background noise may become significant. Take care to set up the input levels for best performance.

When any AFL/PFL switch is pressed, the meters switch to show the selected AFL/PFL signal on both meters, in mono; the SOLO LED also lights.

MIX & SUB-GROUP OUTPUTS

13 MIX FADER

The MIX FADER sets the final level of the Mix outputs. This should normally be set close to the ‘0’ mark if the input GAIN settings have been correctly set, to give maximum travel on the fader for smoothest control.

14 SUB FADERS

This pair of faders sets the final levels of the Sub-group outputs. These should normally be set close to the ‘0’ mark if the input GAIN settings have been correctly set, to give maximum travel on the faders for smooth- est control.

15 SUB TO MIX

This switch routes the Sub-L and Sub-R signals to the main mix.

16 STEREO/MONO

If this switch is depressed a mono sum of the sub-group signals is routed to the main mix.

17 MIX OUTPUTS

The Mix LEFT and RIGHT outputs are sent from the XLR sockets as balanced signals.

18 MONO OUTPUT

A mono sum of the mix left and right signals is output on this balanced 3-pole 6.35mm (1/4”) jack socket.

19 SUB OUTPUTS

The Sub-L and Sub-R signals are output on these balanced 3-pole 6.35mm (1/4”) jack sockets.

20 RECORD OUTPUTS

These two RCA outputs carry a copy of the MIX L and MIX R signals. They allow the use of a recording device, e.g. DAT player, Minidisc, Cassette tape recorder etc.

AUX

21 AUX MASTERS

These controls set the output levels of the Aux Outputs. (1 & 2 on MFXi, 1, 2 & 3 on MPMi)

22 AFL

These After Fade Listen switches route their respective aux output signal to the headphones, control room output and meters, where it replaces the MIX. The SOLO LED on the Master section illuminates to warn that an AFL is active. There are 2 AFL switches for Auxes 1 &2 on the MFXi, and three for Auxes 1, 2 and 3 on the MPMi.

Soundcraft MFXi MPMi User Guide Issue 1210

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents User Guide Page User Guide Potters BAR Contents Important Safety Instructions Neutral Blue US White Live Hot Brown US Black Safety Symbol Guide Soundcraft MFXi MPMi User Guide Issue Consignes DE Sécurité Importantes Vert et Jaune US Vert/Jaune Avertissement Guide DES Symboles DE SécuritéRemarques Informations utiles sur l’utilisation de la consoleIntroduction Advice for Those WHO Push the Boundaries60-SECOND Guide MFXi SUB-GROUP Routing MIC 60-SECOND Guide MPMiBe monitored also, see item 30 below Mic Input Wiring UPLine Input Insert PointStereo Inputs Stereo 1/2 HeadphonesMix Outputs Aux and FX Bus OutputsPolarity Phase Grounding and ShieldingCables Products Under Warranty Problem SolvingOUT-OF-WARRANTY Products UK customers should contact their local dealerAUX Outputs Block Diagram MFXiMPMi High-pass Filter Mono Input Channels MFXi shownHF EQ MID EQLF EQ PAN Signal Present SP LEDMute Input Channel FaderInputs Stereo 1/2 Stereo Input Channels MFXi shownGain MF EQFader BalancePFL Channel Peak LEDSoundcraft MFXi MPMi User Guide Issue Master Section MFXi Master Section MPMi Phantom Power Power IndicatorHeadphones Level Headphones SocketMIX Fader Meters & Solo LEDSUB Faders SUB to MIXMute FX Footswitch 23 PRE/POST SwitchFX Master FX AFLFX Operation Lexicon FX Processor OverviewSelect and Load a Program Set Audio LevelsFX Processor Controls MFXi only Reverbs Karaoke Reverb ControlsDelays Modulated Effects Delay ControlsPhaser Factory ResetFlanger Tremelo/PanEffects Data Chart Crosstalk @ 1kHz MFXi/MPMi Typical SpecificationsUsing Your MFXi/MPMi Console Microphone PlacementInitial Setup Page STE1 STE2 Effects 48V Used forFitting Optional RACK-MOUNT Brackets Dimensions ExtenderMixer Applications Instrument and Vocal Sources Configurations can be driven by the MFXiPlayer Application 3 Places of WorshipStudio Control Room Application 4 RecordingTypical Connecting Leads ‘Y’ Cables Unbalanced Glossary Position Pre-fadeA highpass or lowpass derived response See aboveBenefit of this Warranty may not be assigned by the End User WarrantySoundcraft MFXi MPMi User Guide Issue Balboa Boulevard Soundcraft Soundcraft USA
Top Page Image Contents