Roland VGA-3 owner manual Type of Settings, GK Setting Settings, GK Direction Setting

Page 12

Settings for the GK Pickup (GK Setup)

The Type of Settings

GK SETTING Settings

You can store three sets of settings in the VGA-3.

This conveniently allows you to prepare separate settings for a multiple number of guitars equipped with a GK pickup.

fig.0022

GK DIRECTION Setting

This sets the direction of the GK pickup's installation.

1.Rotate [GUITAR TYPE] to select “LP” (GK DIRECTION).

Set C

GKSetDIRECTIONB

GK PHASE

GKSetDIRECTIONA

GK S1/S2

GK PHASE

GK DIRECTION

GK SENS 1–6

GK S1/S2

GK PHASE

GK LEVEL

GK SENS 1–6

GK S1/S2

GK LEVEL

GK SENS 1–6

GK LEVEL

1.Rotate [GUITAR TYPE] to select “ST” (GK SETTING).

2.Press a MEMORY button [1]–[3] to select the GK SETTING set you want to enable (the settings you want to change).

Memory button	Setting
[1]	Set A

[2]	Set B

[3]	Set C

2.Press the MEMORY button [1] or [2] to select the direction in which the pickup is attached.

Memory button

Setting

[1]NORMAL

In this direction, the cable exits on the side of string 6.

[2]REVERSE

In this direction, the cable exits on the side of string 1.

fig.0030

NORMALREVERSE

string 6 string 1

string 6 string 1

*There is no need to change the settings if you are making them for the first time or if you are not using multiple GK settings. In this case, select [1] Set A, the factory default setting.

*If it is difficult to determine the direction in which the GK pickup was installed on a GK compatible guitar, try it out initially at the [1] NORMAL setting.

If there is no response from the meter when you play string 6 during the GK SENS 6 settings (p. 13), but there is a response when you play string 1, change the setting to [2] REVERSE.

12

Image 12

Contents Main Features Cosm AmplifierImportant Safety Instructions Page Fig. a Power Supply PlacementMaintenance Additional Precautions Contents Basic Operation Front PanelWrite Button Turning the Power On Rear PanelSettings for the GK Pickup GK Setup Preparations for using the GK PickupBasic Setting Procedure Type of Settings GK Setting SettingsGK Direction Setting GK Phase Setting GK S1/S2 SettingGK Sens 6-1 Settings Rotate Guitar Type to selectGK Level Setting Finishing the GK SetupGK Setup Chart Press TunerList of Guitar Types ElectricAcoustic SpecialMore Advanced Operation Synth FilterPoly Octave String Select Select Poly Octave Press Pickup to select the patternList of Amp Types StackCombo Effects Setting the Delay Time with TAP Input Changing the Doubling Delay TimeClear WarmPlate SpringStoring Knob and Button Settings to Memory Write Operate the knob for the setting you want to checkCalling Up Memory Press Memory button to select the memory to be called upUsing the GFC-50 to Operate the VGA-3 Connecting the VGA-3 and the GFC-50How to Call Up the VGA-3’s Memories Using the GFC-50 Switching Memories With the GFC-50Storing Writing to the VGA-3’s Memories Using the GFC-50 Control Using an External Foot Switch or PedalPress the VGA-3’s Write 1 once more Making the System Settings System Setup Tuner Pitch SettingTuner Level Setting Start the System SetupNS Threshold Setting Foot SW FS1/FS2 SettingEXP Pedal Mode Setting EXP Pedal Hold SettingMidi Omni Mode Setting System Setup Chart Finishing the System SetupRestoring the Factory Settings When Restoring All Settings to Their Factory SettingsHold down Write while you switch on the Power switch Additional DataPress Write two times Troubleshooting Other ProblemsTrouble with the Sound Block Diagram/Effect Connection Procedure Midi Implementation Chart Specifications VGA-3 V-GUITAR AmplifierMemory Sheet Factory Settings Guitar Type AMP Type EFX Delay ReverbMemo Avis