Roland VGA-3 owner manual Calling Up Memory, Storing Knob and Button Settings to Memory Write

Page 21

MEMORY

You can store and call up ten knob and button settings on the VGA-3. Additionally, with the use of a foot controller (such as the optional GFC-50 or FC-200), you can store and call up forty knob and button settings (p. 22).

*The settings controlled by the following external devices are also stored to the memory along with knob and button settings. Foot Switch (EFX ON/OFF, DELAY ON/OFF), Expression Pedal (VOLUME, GK, WAH)

Calling Up Memory

1.Press MEMORY button to select the memory to be called up.

When the [A/B] button is not lit, the memories numbered from 1 through 5 can be selected.

When the [A/B] button is lit, the memories numbered from 6 through 10 can be selected.

Changing the Memory Settings (Edit)

1.Press memory button to select the memory whose settings are to be changed.

2.Operate the knobs/buttons.

When you change the knob or button settings, the button indicator corresponding to the selected memory flashes.

Immediately after you switch memories, the knob positions may not correspond to the settings stored in the memory. When you turn a knob, the knob’s adjustment function is enabled as you approach the position stored in the memory. If you are not sure of the setting stored in memory, turn the knob completely to the left (counterclockwise); the knob’s function is enabled at that time.

If before the setting is stored the mode is switched to Manual or Memory, or the power is turned off, all changes in the settings will be discarded. Whenever working with important settings, be sure to carry out the Write procedure.

Storing Knob and Button Settings to Memory (Write)

1.When you have finished making the knob and/or button settings, press [WRITE], causing the indicator to flash.

2.Press MEMORY button for the memory in which you want the settings stored.

* If you want to cancel the Write procedure, press [MANUAL].

3.Press [WRITE] once more to carry out the write. During the write, the [WRITE] indicator flashes rapidly; the write is completed when the [WRITE] indicator stops flashing and stays off.

Confirming the Settings Stored in Memory (Memory Utility)

This reproduces the knob positions (settings values) stored in memory.

*This function is disabled whenever [MANUAL] is selected.

*During confirmation, the volume and tone are not changed when any knob other than [MASTER] is rotated.

1.Hold down [TUNER] and press [MANUAL].

* The [TUNER] flashes.

2.Operate the knob for the setting you want to check.

*One of the TUNER meter indicators lights up.

3.While monitoring TUNER meter indicators, rotate the

knob further until the green indicator in the center is lit.

fig.0170

Rotate the knob clockwise

Lit

Correspond to the setting stored in the memory

Rotate the knob counterclockwise

Lit

4.Repeat Steps 2 and 3 for any knob you want to check.

5.Press [TUNER] again to complete the confirmation procedure.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Cosm Amplifier Main FeaturesImportant Safety Instructions Page Fig. a Power Supply PlacementMaintenance Additional Precautions Contents Front Panel Basic OperationWrite Button Rear Panel Turning the Power OnSettings for the GK Pickup GK Setup Preparations for using the GK PickupBasic Setting Procedure Type of Settings GK Setting SettingsGK Direction Setting GK S1/S2 Setting GK Phase SettingGK Sens 6-1 Settings Rotate Guitar Type to selectFinishing the GK Setup GK Level SettingGK Setup Chart Press TunerElectric List of Guitar TypesAcoustic SpecialSynth Filter More Advanced OperationPoly Octave String Select Select Poly Octave Press Pickup to select the patternList of Amp Types StackCombo Effects Changing the Doubling Delay Time Setting the Delay Time with TAP InputClear WarmSpring PlateOperate the knob for the setting you want to check Storing Knob and Button Settings to Memory WriteCalling Up Memory Press Memory button to select the memory to be called upConnecting the VGA-3 and the GFC-50 Using the GFC-50 to Operate the VGA-3How to Call Up the VGA-3’s Memories Using the GFC-50 Switching Memories With the GFC-50Storing Writing to the VGA-3’s Memories Using the GFC-50 Control Using an External Foot Switch or PedalPress the VGA-3’s Write 1 once more Tuner Pitch Setting Making the System Settings System SetupTuner Level Setting Start the System SetupFoot SW FS1/FS2 Setting NS Threshold SettingEXP Pedal Mode Setting EXP Pedal Hold SettingSystem Setup Chart Finishing the System Setup Midi Omni Mode SettingWhen Restoring All Settings to Their Factory Settings Restoring the Factory SettingsHold down Write while you switch on the Power switch Additional DataPress Write two times Troubleshooting Other ProblemsTrouble with the Sound Block Diagram/Effect Connection Procedure Midi Implementation Chart VGA-3 V-GUITAR Amplifier SpecificationsGuitar Type AMP Type EFX Delay Reverb Memory Sheet Factory SettingsMemo Avis
Top Page Image Contents