Lennox Hearth 2800HT operation manual Blower System, Wiring Diagram Power Flow Diagram

Page 15

CARE AND OPERATION

BLOWER SYSTEM

The Blower System consists of a ON / OFF rocker switch, a variable speed blower speed control switch (rheostat) located on the right side panel, a thermally activated switch (fan disc) and 4 axial blowers.

When starting a fire, leave the blower system off until the insert is thoroughly heated (approx. 30 minutes after start up).

The blowers can be operated in one of the fol- lowing manners:

Auto: Turn rocker switch to the off position ( “O” = off, “—“ = on). Turn the rheostat to the on position by rotating the rheostat dial clockwise until it clicks. When the insert warms up (110° F), the blower will automatically turn on (adjust rheostat dial to the desired speed setting). When the insert cools down (90° F), the blow- ers will automatically turn off.

Manual: Turn rocker switch to the on ( — ) position and adjust rheostat dial to the desired speed. The blowers will have to be manually turned off by rotating the rheostat dial counter- clockwise until it clicks.

BLOWER SPECIFICATIONS: 115 V, 60 Hz, two axial blowers - .42 amps each, 125 CFM each. Blower system has a flexible electrical cord that must be electrically grounded per lo- cal codes or NEC, ANSI / NFPA 70-latest edi- tion. Do not route the power cord under or in front of the appliance.

Blower System Controls

Located on right side of door at bottom of panel

WIRING DIAGRAM

POWER FLOW DIAGRAM

CAUTION: BURNING THE INSERT AT A HIGH BURN RATE FOR EXTENDED PERIODS WITHOUT RUNNING THE BLOW- ERS CAN CAUSE EXCESSIVE TEMPERATURES RESULTING IN OVERFIRING DAMAGE TO THE APPLIANCE. EXCESSIVE HEAT WILL CAUSE THE PROPELLERS ON THE BLOWERS TO MELT. IF THIS OCCURS, REPLACE PROPELLERS AND RE- VIEW THESE INSTRUCTIONS FOR PROPER OPERATION (PROPELLER PART / CATALOG #410-25-3. SOME PEOPLE PREFER METAL PROPELLERS, WHICH ARE AVAILABLE THROUGH GRAINGER, STOCK #2C953. BE ADVISED THAT THESE ARE NOISIER THAN STANDARD PLASTIC BLADES). OVERFIRING DAMAGE IS NOT COVERED UNDER THE 5 YEAR PRORATED WARRANTY.

WARNING: THIS APPLIANCE IS EQUIPPED WITH A BLOWER SYSTEM WHICH HAS A FLEXIBLE ELECTRICAL POWER CORD WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE PER LOCAL CODES OR NEC, ANSI / NFPA 70 - LATEST EDITION. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THE POWER CORD PLUG. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE.

PAGE 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 775004M, Rev. J, 11/03 Installation and Operation ManualImportant Warnings Table of Contents Chimney Inspection Planning Your InstallationSmoke Detectors Hearth ProtectionClearances Draft RequirementsProvide Adequate AIR for Combustion Venting Requirements for factory built fireplace Factory Built Fireplace InstallationFactory Built Fireplaces Not Approved In CanadaMetal Tag Masonry FireplacesInstallation Marble Power Cord ChangeoverInstallation Steps Baffle PlateWrong CorrectSurround Assembly Primary AIR Control Product Features and ControlsPositive Flue Connection for Masonry Blower SystemCare and Operation Refueling HOW to Start and Maintain a FireAIR Draft Controls Start-Up Air ControlWiring Diagram Power Flow Diagram Fuel MaintenanceRemoval of Fireplace Insert for Inspection Cleaning BlowersServicing Glass Replacing GlassReinstall Baffle Plate Cleaning / Removing Baffle Plate To remove, locateTroubleshooting Overfiring Damage Dimensions shown are approximations only +/- ¼ 6.4 mm BTU63% Gph Lbs kg Manual Cfm total Description Replacement Parts List Model 2800HTReplacement Parts List Model 2800HT Component Diagrams Model 2800HT Zero Clearance Kit SAFETY/LISTING LabelOffset Adapter Actual Appearance Masonry Fireplace KitSAFETY/LISTING Label EPA Label Ownership Records Service and Maintenance LOGWest Taft Avenue Orange, CA
Top Page Image Contents