Philips CS-E15DB4EW specifications Evacuation of the Equipment

Page 63

CS-E15DB4EW CU-E15DBE / CS-E18DB4EW CU-E18DBE / CS-E21DB4ES CU-E21DBE

11.3.4. EVACUATION OF THE EQUIPMENT

WHEN INSTALLING AN AIR CONDITIONER, BE SURE TO EVACUATE THE AIR INSIDE THE INDOOR UNIT AND PIPES in the following procedure.

1.Connect a charging hose with a push pin to the Low and High side of a charging set and the service port of the 3-way valve.

•Be sure to connect the end of the charging hose with the push pin to the service port.

2.Connect the center hose of the charging set to a vacuum pump with check valve, or vacuum pump and vacuum pump adaptor.

3.Turn on the power switch of the vacuum pump and make sure that the needle in the gauge moves from 0 cmHg (0 MPa) to -76 cmHg (-0.1 MPa). Then evacuate the air approximately ten minutes.

4.Close the Low side valve of the charging set and turn off the vacuum pump. Make sure that the needle in the gauge does not move after approximately five minutes.

Note: BE SURE TO FOLLOW THIS PROCEDURE IN ORDER TO AVOID REFRIGERANT GAS LEAKAGE.

5.Disconnect the charging hose from the vacuum pump and from the service port of the 3-way valve.

6.Tighten the service port caps of the 3-way valve at torque of 18 N.m with a torque wrench.

7.Remove the valve caps of both of the 2-way valve and 3-way valve. Position both of the valves to “OPEN” using a hexagonal wrench (4 mm).

8.Mount valve caps onto the 2-way valve and the 3-way valve.

•Be sure to check for gas leakage.

CAUTION

•If gauge needle does not move from 0 cmHg (0 MPa) to -76 cmHg (-0.1 MPa), in step 3 above take the following measure:

•If the leak stops when the piping connections are tightened further, continue working from step 3.

•If the leak does not stop when the connections are retightened, repair the location of leak.

•Do not release refrigerant during piping work for installation and reinstallation. Take care of the liquid refrigerant, it may cause frostbite.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Contents Environmental Protection FeaturesServiceability Improvement ProductFunctions Remote ControlIndoor Unit Automatic Operation SwitchOutdoor Unit CS-E15DB4EW CU-E15DBE Product SpecificationsFPI CS-E18DB4EW CU-E18DBE CS-E18DB4EW CU-E18DBENet Weight Lb kg CS-E21DB4ES CU-E21DBE CS-E21DB4ES CU-E21DBE108 Dimensions Indoor Unit & Remote ControlCS-E15DB4EW CS-E18DB4EW CS-E21DB4ES CU-E15DBE CU-E18DBE CU-E21DBE Refrigeration Cycle Diagram Block Diagram Wiring Diagram Temperature Shifting Flow Operation DetailsBasic Operation Cooling Operation Thermostat control Soft Dry Operation Thermostat controlHeating Operation Thermostat control Automatic Operation Indoor Fan Motor Operation Basic Rotation Speed rpmIndoor Fan Control Heating Ii. Auto Fan Speed Cooling Fan Motor Control Deodorizing Control Outdoor Fan Motor OperationPurpose Quiet operation Cooling Mode/Cooling area of Dry ModeAirflow Direction Vertical AirflowQuiet operation Heating Control contentsOFF Timer Powerful Mode OperationHour Real Time Timer Control On TimerDrain Pump Control Operation Drain Pump ErrorAuto Restart Control Indication PanelTotal Running Current Control Protection Control FeaturesIPM Power transistor Prevention Control Seconds Forced OperationControl start conditions Compressor Overheating Prevention ControlLow Pressure Prevention Control Gas Leakage Detection Low Frequency Protection ControlCooling Overload Control Anti-Dew Formation Control Anti-Freezing ControlOverload Protection Control Deice Control Operating Instructions Page Page Page Page Page Page Page Installation And Servicing Air Conditioner Using R410A OutlineAbout R410A Refrigerant Necessary Tools Tools For Installing/Servicing Refrigerant PipingTorque wrenches 10.2.2. R410A ToolsSensitivity with R410A is about 23 g/year Electronic scale for refrigerant charging 10.2.3. R410A Tools Which Are Usable for R22 ModelsProcessing and Connecting Piping Materials Refrigerant Piping WorkPiping Materials Storing and Managing Piping Materials Precautions Installation, Transferring, ServicingAC Units Replacement Using Existing Refrigerant Piping Transferring Using New Refrigerant PipingRecharging Refrigerant During Servicing PrecautionBrazing Servicing TipsBrazing Method for Preventing Oxidation Safety Precautions Installation InstructionsPage Attached accessories Select the best locationOutdoor Unit Page Installation of Indoor Unit Vacuum drying Indoor Unit Drain PipingWall seal Heat InsulationConnecting the Cable to the Indoor Page Cutting and Flaring the Piping Connecting The Piping To Indoor UnitConnecting The Piping To Outdoor Unit Refer to Select the best location sectionEvacuation of the Equipment Disposal of Outdoor Unit Drain Water Auto Switch OperationHand Over Changing the Remote Control Transmission CodeREMO-CON NO. Change in Remote Control Check ItemsTroubleshooting Servicing InformationRated Frequency Operation Troubleshooting Air Conditioner Refrigeration cycle system Breakdown Self Diagnosis Function Judgement Error Codes TableSetting Remote Control Transmission Code Remote Control ResetAuto OFF/ON Button Disassembly of Parts Page Remove the top panel and front panel Outdoor Electronic Controller Removal ProcedureTechnical Data Operation CharacteristicsCS-E15DB4EW CU-E15DBE CS-E18DB4EW CU-E18DBE CS-E21DB4ES CU-E21DBE CS-E21DB4ES CU-E21DBE Sensible Capacity ChartCS-E15DB4EW CU-E15DBE CS-E18DB4EW CU-E18DBECS-E15DB4EW CS-E18DB4EW CS-E21DB4ES Exploded View Indoor UnitPage CZ-BT20E Front Grille Complete Replacement Parts List Indoor Unit REF. no Part Description QTY Front Grille Complete CU-E15DBE CU-E18DBE CU-E21DBE Exploded View Outdoor UnitReplacement Parts List Outdoor Unit CS-E15DB4EW CS-E18DB4EW CS-E21DB4ES Schematic Diagram 1/4 Electronic Circuit DiagramR17 Schematic Diagram 2/4SSR02 SSR01 Schematic Diagram 3/4WHT Schematic Diagram 4/4CU-E15DBE CU-E18DBE CU-E21DBE Schematic Diagram 1/4 FUSE2 IC1 Yellow Schematic DiagramHow to use electronic circuit diagram Timer Table IndoorTimer Table Outdoor Remote Control Print Pattern Indoor Unit Printed Circuit Board Print Pattern Outdoor Unit Printed Circuit Board View

CS-E15DB4EW specifications

The Philips CS-E15DB4EW is an exceptional air conditioner that exemplifies modern cooling technology while emphasizing energy efficiency and user comfort. This model is designed to provide reliable performance in various settings, making it suitable for both residential and light commercial applications.

One of the standout features of the Philips CS-E15DB4EW is its powerful cooling capacity. With a cooling power reaching up to 15000 BTUs, this air conditioner is capable of effectively cooling medium to large-sized rooms. This high capacity ensures that users enjoy a refreshingly cool environment, even during the hottest summer months.

Energy efficiency is a prominent characteristic of the CS-E15DB4EW. It features an advanced inverter technology that optimizes power consumption while maintaining the desired temperature. This technology not only results in lower electricity bills but also reduces environmental impact by minimizing energy waste. The air conditioner boasts a high EER (Energy Efficiency Ratio), making it a responsible choice for energy-conscious consumers.

In terms of convenience, the CS-E15DB4EW is equipped with a user-friendly remote control, allowing users to adjust settings from a distance. This includes temperature adjustments, fan speed settings, and timer functions, providing flexibility and comfort at the users' fingertips. Additionally, the air conditioner features various operating modes, including cool, dry, and fan modes, catering to diverse climatic conditions and individual preferences.

Another remarkable characteristic of the Philips CS-E15DB4EW is its quiet operation. With a noise level as low as 30 dB, this unit ensures that users can enjoy a peaceful environment without the disruptive sounds typical of standard air conditioning units. This feature is particularly beneficial for bedrooms or study areas where concentration or relaxation is crucial.

Moreover, the unit is designed with a sleek, modern aesthetic that seamlessly integrates into any interior decor. The easy-to-clean filters and compact design contribute to its practicality, allowing for efficient maintenance and longevity.

In conclusion, the Philips CS-E15DB4EW stands out as a versatile, efficient, and user-friendly air conditioning solution. With its powerful cooling capacity, energy-saving technologies, convenient features, and quiet operation, it effectively addresses the cooling needs of various environments. Whether for residential use or light commercial applications, this model is designed to provide a comfortable atmosphere while being mindful of energy consumption and environmental impact.
Top Page Image Contents