GE X-9 owner manual Booth outputs, Microphone connection and use

Page 11

When connecting an ampli- fication system to the X-9,

or

check the inputs of the

amplifier. If they look like either of the connectors shown here, they are XLR connectors and are probably balanced.

Check the rear panel of the amplifier, or the ampli- fier’s manual, to make sure. Amplifiers with bal- anced inputs should be fed by the MASTER OUTPUT (BALANCED) output connectors of the X-9.

All other connectors (mono 1/4” jack or RCA pin jacks should be fed by the (UNBALANCED) RCA pin outputs.

The level of the output from the unbalanced outputs can be set using the PRE/POST switch to be affected by the master fader (POST) or unaffected by it (PRE).

3 Connections

WARNING

It is most important to make sure that you make the correct connections. Connecting the wrong output of the X-9 to the amplification system can result in over- heating and possible damage to both the X-9 and to the amplification system.

If you are in any doubt at all, we strongly suggest that you consult your TASCAM dealer or other qualified audio professional regarding the interconnection of your system.

Use the trimmer potentiometers (LEVEL ATT) to adjust the output level to the amplification systems. Again, you may find it useful to consult the amplifi- cation system documentation and/or consult a profes- sional sound engineer.

Booth outputs

The booth outputs provide you with a sec- ond mix where the level is not controlled by the master fader, but by the BOOTH LEVEL volume control.

Connect the unbalanced BOOTH OUTPUT RCA jacks to the unbalanced inputs of the booth amplification system.

Microphone (connection and use)

To input your voice through the X-9 sys- tem, you need to connect a microphone to the system. The X-9 provides an XLR connector for connecting a standard (dynamic) microphone.

Connect your favorite microphone to this connector.

Use the TALK OVER key to “dim” all the signals except the microphone by 20 dB (the key lights when active).

Adjust the level of the microphone sig- nal sent to the master fader with the LEVEL control.

Adjust the tone of the microphone signal with the HI (treble) and LO (bass) EQ controls.

Use the menu system (18bm) to change the left-right balance of the microphone signal.

You can also select the microphone signal to be passed through the internal or external effects, as well as being used as a source for sampler 1.

The microphone signal can be cued (see “Cue (pre- viewing sounds)” on page 16) in the same way as program signals, using the CUE key (lights when active).

TASCAM X-9Owner’s Manual 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Professional Digital DJ Mixer Important Safety Precautions Important Safety Instructions Table of Contents Environmental considerations Some notes and precautionsIntroduction Serial number, etcProgram gain level, EQ and assignment section Getting acquainted withRoad map to front panel functions Cue selection keys and monitor keys Sampler sectionMicrophone control External effect Master faderProgram faders Effect, menu, etc. management Cross-fader and fader controlsDigital connections ConnectionsRecord turntables CD decks, etcMicrophone connection and use Booth outputsFader start/stop connections Headphones connecting and usingFootswitches External effects unitTo use the external effects unit External effectsAssigning sources to programs Learning moreAbout programs Cross-fadingSignal flow Cue previewing sounds Adjusting the output volumePlaying a song Menu reference How the X-9 shows charactersMenus Meter peak hold Program EQ QValues Meter release timeProgram 1 balance Restore factoryPresets Mic balanceFader start FadersProgram fader curve Program fader directionCross-fader reverse Cross-fader curveCross-fader start Beat parameter EffectsSelecting the effect type Editing the effectsStoring effects Effect parametersLPFa Recalling stored effect settings Playing back samples SamplersRecording a sample Sample pitch Editing samplesErasing samples Cutting the EQ bands EQ Q settingViewing EQ settings Remembering and recalling EQ settings Control I/O Specifications, etcSpecifications Audio I/OGeneral specifications Audio specificationsDimensional drawing Case mounting Mounting the X-9 in a rackEtc Block diagramPage Teac Corporation
Top Page Image Contents