GE X-9 owner manual Important Safety Precautions

Page 2

Important Safety Precautions

IMPORTANT (for U.K. Customers)

DO NOT cut off the mains plug from this equipment.

If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not provided with a mains plug, or one has to be fitted, then follow the instructions given below:

IMPORTANT: DO NOT make any connection to the larger terminal which is marked by the letter E or by the safety earth symbol ç or coloured GREEN or GREEN-and-YELLOW.

The wires in this mains lead are coloured in accordance with the following code:

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover.

IF IN DOUBT — CONSULT A COMPETENT ELECTRICIAN.

For U.S.A

TO THE USER

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residental area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION

Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user’s authority to operate this equipment.

For the consumers in Europe

WARNING

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Pour les utilisateurs en Europe

AVERTISSEMENT

Il s’agit d’un produit de Classe A. Dans un environnement domestique, cet appareil peut provoquer des interférences radio, dans ce cas l’utilisateur peut être amené à prendre des mesures appropriées.

Für Kunden in Europa

Warnung

Dies is eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung kann im Wohnbereich Funkstörungen versursachen ; in diesem Fall kann vom Betrieber verlang werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.

The equipment draws nominal non-operating power from the

AC outlet with its POWER switch in the off position.

2 TASCAM X-9 Owner’s Manual

Image 2
Contents Professional Digital DJ Mixer Important Safety Precautions Important Safety Instructions Table of Contents Serial number, etc Some notes and precautionsIntroduction Environmental considerationsProgram gain level, EQ and assignment section Getting acquainted withRoad map to front panel functions Cue selection keys and monitor keys Sampler sectionMicrophone control External effect Master faderProgram faders Cross-fader and fader controls Effect, menu, etc. managementCD decks, etc ConnectionsRecord turntables Digital connectionsBooth outputs Microphone connection and useExternal effects unit Headphones connecting and usingFootswitches Fader start/stop connectionsExternal effects To use the external effects unitCross-fading Learning moreAbout programs Assigning sources to programsSignal flow Cue previewing sounds Adjusting the output volumePlaying a song How the X-9 shows characters Menu referenceMenus Meter release time Program EQ QValues Meter peak holdMic balance Restore factoryPresets Program 1 balanceProgram fader direction FadersProgram fader curve Fader startCross-fader reverse Cross-fader curveCross-fader start Editing the effects EffectsSelecting the effect type Beat parameterStoring effects Effect parametersLPFa Recalling stored effect settings Playing back samples SamplersRecording a sample Sample pitch Editing samplesErasing samples Cutting the EQ bands EQ Q settingViewing EQ settings Remembering and recalling EQ settings Audio I/O Specifications, etcSpecifications Control I/OAudio specifications General specificationsDimensional drawing Mounting the X-9 in a rack Case mountingBlock diagram EtcPage Teac Corporation