Fostex DE-10 When selecting Single, Single 1/2 mode, these controls and indi Cators are not used

DE-10 Owner’s Manual

In the single (1/2) mode, these controls and indi-

cators are not used.

				TYPE			VARIATION
2	MODE	SINGLE1/DUAL	SINGLE 2	F			6
L	G	DELAY	DISTORTION	E	G	5	7
L	H	MISC	G.MULTI 1	D	H	4	8
	I	CHORUS	G.MULTI 2	C	I	3	9
	J	PITCH	B.MULTI	B	J	2	10
M	K	FLANGER	VO.MULTI	A	K	1	11
M
					PEAK

ADJUST PARAM.1

EFFECT 2

	MIX			TYPE	VARIATION		ADJUST	MIX
DRY+EFF							PARAM.2	PARAM.3
				DLY+REV	6		DRY+EFF
	MODE		VOCAL	DELAY	5	7
	SINGLE2		PLATE	MISC	4	8
	SINGLE1	DUAL	ROOM	CHO	3	9		EFF MUTE
DRY	EFF		S.HALL	PITCH	2	10	DRY	EFF
			L.HALL	FLANGE	1	1 1
				PEAK				POWER

2 3 4 5 1 4 4

<Front panel settings>

1.Set the MODE switch to "SINGLE 1" or "SINGLE 2".

2.Set the TYPE switch to the desired position.

You can select from among the following eleven types for each single mode. See page 8~15 for details about each type.

• When selecting "SINGLE 1".

SW MODE	SINGLE 1/DUAL	SINGLE 2	SW MODE	SINGLE 1/DUAL	SINGLE 2
A	L. HALL	L. HALL	G	DELAY	DISTORTION
B	S. HALL	S. HALL	H	MISC	G. MULTI 1
C	ROOM	ROOM	I	CHORUS	G. MULTI 2
D	PLATE	PLATE	J	PITCH	B. MULTI
E	VOCAL	MIC SIM	K	FLANGER	VO. MULTI
F	DELAY + REV	AMP SIM

• When selecting "SINGLE 2".

SW MODE SINGLE 1/DUAL		SINGLE 2	SW MODE SINGLE 1/DUAL		SINGLE 2
A	L. HALL	L. HALL	G	DELAY	DISTORTION
B	S. HALL	S. HALL	H	MISC	G. MULTI 1
C	ROOM	ROOM	I	CHORUS	G. MULTI 2
D	PLATE	PLATE	J	PITCH	B. MULTI
E	VOCAL	MIC SIM	K	FLANGER	VO. MULTI
F	DELAY + REV	AMP SIM

<About PEAK indicator>

The PEAK indicator on the front panel illuminates when the input signal to be monitored reaches 6 dB below the clipping level. Adjust the input level appropriately so that the PEAK indicator occasionally flickers.

If you hear the output sound distorted though the PEAK indicator does not steadily light or illuminate so often, it may be due to the signal level increase in the effect processing. In such a case, reduce the input level so that the output sound is not distorted.

<Note on changing the switch position>

When you change the position of the MODE, EFFECT TYPE, or VARIATION switch, the DE-10 resets the internal DSP and the output signal disappears momentarily. This is due to not a malfunction.

<Notes on using the ADJUST and MIX controls>

•When you turn the ADJUST or MIX control, a click may be generated with some effect type.

•If the default of a parameter is the maximum or minimum value, you cannot increase or decrease the value using the ADJUST control, respectively.

3.Set the VARIATION switch to the desired position.

4.Using the ADJUST (PARAM 1 through PARAM 3) controls, adjust the effect parameters.

In the single mode, you can control three parameters for each effect, as shown in the table below.

5.Using the MIX control, adjust the mixing balance of dry and effect signals fed from the appropriate OUTPUT jacks.

20