ClearOne comm AP800 operation manual Appendix a Specifications, Fcc, Csa, Ce

Page 37

Appendices

Appendix A: Specifications

Dimensions (LxDxH)

17.25" x 10.25" x 1.75" 43.8 x 26 x 4.5 cm

Weight

7 lb/4.5 kg dry

12 lb/5.9 kg shipping

Operating Temperature

32–100° F/0–38° C

Humidity

15% to 80%, non-condensing

Power Input Range

Auto-adjusting

100–240VAC; 50/60Hz

Power Consumption

30W typical

G-Link In/Out Proprietary Network RJ-45 (2), 38.4kbps,

110kΩ impedance Category five twisted-pair cable

20' (6 meters) maximum cable length between any two Audio Perfect products

RS-232

DB-9 female

9,600 (default)/19,200/38,400 baud rate; 8 bits, 1 stop, no parity

Hardware flow control on (default)/off

Control/Status

DB-25 female A/B (2)

Inputs A/B: active low (pull to ground)

Outputs A/B: Open collector, 40VDC max, 40mA each

+5VDC pins (2) (300mA over-current protected)

Mic/Line Inputs 1-8

Push-on terminal block, balanced, bridging

Impedance: 5kΩ

Nominal Level: adjustable -55dBu, -25dBu, 0dBu

Maximum Level: -33dBu, -4dBu, +20dBu

Echo Cancellation: 120ms tail time (works with 12dB of room gain)

Phantom Power: 24V, selectable

Line Inputs A-D

Push-on terminal block, balanced, bridging

Impedance: >20kΩ

Nominal Level: 0dBu

Maximum Level: 19dBu

Outputs 1-12

Push-on terminal block, balanced Impedance: 50Ω

Nominal Level: 0dBu

Maximum Level: 19dBu

Audio Performance

Conditions: Unless otherwise specified, all measurements are performed with a 22Hz to 22kHz BW limit (no weighting).

Frequency Response: 20Hz–15kHz ±2dB

Noise (EIN): -125dBu, 15kHz BW, max gain, Rs=150Ω

THD+N: <0.1%

SNR: 65dB re 0dBu

Dynamic Range: 85dB

Approvals

FCC, CSA, CE

Matrix Mixing Parameters

12x12 matrix

Auto Mixer Parameters

Number of Open Microphones (NOM)

PA Adaptive Mode

First Mic Priority Mode

Last Mic Mode

Maximum # of Mics Mode

Ambient Level

Gate Threshold Adjust

Off Attenuation Adjust

Hold Time

Decay Rate

Microphone Input Configuration

Input Gain Adjust Mic or Line Level Phantom Power on/off Echo Cancellation on/off Mute on/off Chairman Override on/off High Pass Filter

EQ Adjust AGC on/off

Auto Gate/Manual Gate/Gate override Adaptive Ambient on/off

Set-up Software

AP-Ware

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 36 Page 38
Image 37
Page 36 Page 38
Contents AP800 Audio Conferencing System AP800 Installation ClearOne Part No July 2002 Rev Table of Contents Appendices AP-Ware SoftwareProduct Overview IntroductionFeatures Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbHControls and Connections UnpackingFront panel Introduction ~ Controls and Connections Rear panelLink bus Link NetworkLink network will allow interconnection of up to eight Equipment placement Power requirementsEquipment Requirements Auxiliary equipmentConnecting the unit Hardware SetupTo connect the AP800 Networking Units Installation ~ InstallationLink connections To create a G-Link network Device IDsTo set the device ID Installation ~ Installation Device types Mixer ModeErrors To set mixer modeEC reference Switching from one main menu category to another Installation ~ LCD ProgrammingLCD Programming Menu TreesInstallation ~ LCD Programming Adjusting a valueSystem parameters Select PresetLock Panel Set PasscodeDevice ID PA Adaptive ModeUnit ID Gate ParametersMaximum Number of Mics Last Mic ModeFirst Mic Priority Gate RatioDecay Rate Hold TimeManual Ambient RS-232To determine ambient level Baud RateClear Password Modem ModeSerial Overrun Errors TimeoutInputs 1-8, Input Global Input ParametersThree-Band EQ High Pass FilterChairman Mic Adaptive AmbientNLP Adjust Echo CancellerInputs A, B, C, D AEC ReferenceRouting Parameters Output ParametersOutputs 1-8, A-D Subbus 1Routing Guidelines Echo Cancellation SetupInternal Subbus Master Unit EC Reference busSlave Unit Meter Parameters Default MeterInputs, Outputs, ERL, and Erle Technical Services Group ~ 1-800-283-5936 USA ~ AP-Ware software requirements Description64MB RAM To install AP-Ware Installing AP-WareVolume Control Remote ControlTo increase volume To decrease volumeTo mute an input MutingTo mute an output FCC, CSA, CE Appendix a SpecificationsThis warranty is void if Appendix B WarrantyFCC Part 15 compliance Appendix C ComplianceAppendices ~ Appendix C Compliance Pin Number Definable Status Default Description Appendix D Connector PinoutsControl/Status a pinout Control/Status B pinout Pin Number User Definable* Status Default Description+5VDC Control/Status Pinout NoteAppendices ~ Appendix E Accessories Appendix E AccessoriesRS-232 COM DCE Port Pinout Pin Number ControlCommand syntax Appendix F Serial CommandsAppendices ~ Appendix F Serial Commands Mref40Appendices ~ Appendix F Serial Commands Error Codes AP800 Serial CommandsCommand Function AGC AambAmblvl ExplanationDecay BaudChairo DfltmErle ERLFMP FlowFPP Gate GainExamples ExampleGratio GmodeHold LFPLVL LMOMaster MEQ MdmodeDevice Mdmode Device MEQ CH BandMinit MHPMline MmaxMtrx MpassMref InputMtrx 18 OutputmixNLP MuteDevice Mute CH W Device NLP CHOffa NOMDevice NOM CH Device PAAExample PcmdPevnt Event List LFP, PRESET, MUTE, GAIN, AGC, EQ, GMODE, ChairoDevice Pevnt Location Event EventRefsel PresetTout VER UIDDevice UID Device VER~ Appendix G SWorksheets Routing Matrix SetupInputs = Gated AppendicesAppendices ~ Appendix G Worksheets Systemwide Parameters Auto Mix ParametersBus Glossary ~ A-D GlossaryGlossary ~ E-S Glossary ~ T-Z Index ~ A-Z Index
Top Page Image Contents