ClearOne comm operation manual AP800 Installation ClearOne Part No July 2002 Rev

Page 2

rights reserved. No part of this document may

be reproduced in any form or by any means

without written permission from ClearOne

Communications, Inc. Printed in the United

States of America. ClearOne Communications,

Inc. reserves specific privileges. Information in

this document is subject to change without

notice.

AP800 Installation and

Operation Manual

ClearOne Part No. 800-150-001

July 2002 (Rev. 3.0)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 2

Contents AP800 Audio Conferencing System AP800 Installation ClearOne Part No July 2002 Rev Table of Contents AP-Ware Software AppendicesIntroduction Product OverviewFeatures Technical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHFront panel UnpackingControls and Connections Rear panel Introduction ~ Controls and ConnectionsLink network will allow interconnection of up to eight Link NetworkLink bus Equipment Requirements Power requirementsEquipment placement Auxiliary equipmentTo connect the AP800 Hardware SetupConnecting the unit Link connections Installation ~ InstallationNetworking Units To set the device ID Device IDsTo create a G-Link network Mixer Mode Installation ~ Installation Device typesEC reference To set mixer modeErrors LCD Programming Installation ~ LCD ProgrammingSwitching from one main menu category to another Menu TreesAdjusting a value Installation ~ LCD ProgrammingLock Panel Select PresetSystem parameters Set PasscodeUnit ID PA Adaptive ModeDevice ID Gate ParametersFirst Mic Priority Last Mic ModeMaximum Number of Mics Gate RatioHold Time Decay RateTo determine ambient level RS-232Manual Ambient Baud RateSerial Overrun Errors Modem ModeClear Password TimeoutInput Parameters Inputs 1-8, Input GlobalChairman Mic High Pass FilterThree-Band EQ Adaptive AmbientInputs A, B, C, D Echo CancellerNLP Adjust AEC ReferenceOutputs 1-8, A-D Output ParametersRouting Parameters Subbus 1Internal Subbus Echo Cancellation SetupRouting Guidelines Slave Unit EC Reference busMaster Unit Inputs, Outputs, ERL, and Erle Default MeterMeter Parameters Technical Services Group ~ 1-800-283-5936 USA ~ 64MB RAM DescriptionAP-Ware software requirements Installing AP-Ware To install AP-WareTo increase volume Remote ControlVolume Control To decrease volumeTo mute an output MutingTo mute an input Appendix a Specifications FCC, CSA, CEAppendix B Warranty This warranty is void ifAppendices ~ Appendix C Compliance Appendix C ComplianceFCC Part 15 compliance Control/Status a pinout Appendix D Connector PinoutsPin Number Definable Status Default Description +5VDC Pin Number User Definable* Status Default DescriptionControl/Status B pinout Control/Status Pinout NoteRS-232 COM DCE Port Pinout Appendix E AccessoriesAppendices ~ Appendix E Accessories Pin Number ControlAppendices ~ Appendix F Serial Commands Appendix F Serial CommandsCommand syntax MrefCommand Function AP800 Serial Commands40Appendices ~ Appendix F Serial Commands Error Codes Amblvl AambAGC ExplanationChairo BaudDecay DfltmERL ErleFPP FlowFMP Examples GainGate ExampleHold GmodeGratio LFPMaster LMOLVL Device Mdmode MdmodeMEQ Device MEQ CH BandMline MHPMinit MmaxMref MpassMtrx InputOutputmix Mtrx 18Device Mute CH W MuteNLP Device NLP CHDevice NOM CH NOMOffa Device PAAPcmd ExampleDevice Pevnt Location Event Event List LFP, PRESET, MUTE, GAIN, AGC, EQ, GMODE, ChairoPevnt EventTout PresetRefsel Device UID UIDVER Device VERInputs = Gated Routing Matrix Setup~ Appendix G SWorksheets AppendicesSystemwide Parameters Auto Mix Parameters Appendices ~ Appendix G WorksheetsBus Glossary Glossary ~ A-DGlossary ~ E-S Glossary ~ T-Z Index Index ~ A-Z