ClearOne comm AP800 operation manual Pcmd, Example

Page 58

54

PCMD

This command programs or returns the program of the GPIO control pins from the serial port. COMMAND can be any valid command. These values are not part of the preset and do not change when presets are loaded.

[DEVICE] PCMD <LOCATION> <COMMAND>

Explanation

<LOCATION>

LOCATION=1	Control A pin 1 active
LOCATION=2	Control A pin 1 inactive
LOCATION=3	Control A pin 3 active
LOCATION=4	Control A pin 3 inactive
LOCATION=5	Control A pin 5 active
LOCATION=6	Control A pin 5 inactive
LOCATION=7	Control A pin 7 active
LOCATION=8	Control A pin 7 inactive
LOCATION=9	Control A pin 9 active
LOCATION=10	Control A pin 9 inactive
LOCATION=11	Control A pin 11 active
LOCATION=12	Control A pin 11 inactive
LOCATION=13	Control A pin 13 active
LOCATION=14	Control A pin 13 inactive
LOCATION=15	Control A pin 15 active
LOCATION=16	Control A pin 15 inactive
LOCATION=17	Control B pin 1 active
LOCATION=18	Control B pin 1 inactive
LOCATION=19	Control B pin 3 active
LOCATION=20	Control B pin 3 inactive
LOCATION=21	Control B pin 5 active
LOCATION=22	Control B pin 5 inactive
LOCATION=23	Control B pin 7 active
LOCATION=24	Control B pin 7 inactive
LOCATION=25	Control B pin 9 active
LOCATION=26	Control B pin 9 inactive
LOCATION=27	Control B pin 11 active
LOCATION=28	Control B pin 11 inactive
LOCATION=29	Control B pin 13 active
LOCATION=30	Control B pin 13 inactive

Appendices ~ Appendix F: Serial Commands

LOCATION=31	Control B pin 15 active
LOCATION=32	Control B pin 15 inactive

<COMMAND>

COMMAND=String Pin will execute string when actuated

COMMAND=Null Parameter to return the current programming for the pin

COMMAND=Clear Parameter to clear current programming (do nothing state)

COMMAND LIST: LFP, PRESET, MUTE, GAIN, AGC, EQ, GMODE, CHAIRO

Return Values

The command will return the updated condition of the pin in the same format as the command. If the command did not alter the state, the command returns the current command for which the pin is programmed.

Example

The PCMD command line contains both the PCMD command and the command being programmed. To program AP800 unit 0 control A pin 1 to toggle mute on mic 1, the command would appear as follows: #10 PCMD 1 MUTE 1 I 2 (toggles mute to the opposite state: ON to OFF and vice versa)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 58

Contents AP800 Audio Conferencing System AP800 Installation ClearOne Part No July 2002 Rev Table of Contents AP-Ware Software AppendicesIntroduction Product OverviewFeatures Technical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHControls and Connections UnpackingFront panel Rear panel Introduction ~ Controls and ConnectionsLink bus Link NetworkLink network will allow interconnection of up to eight Equipment Requirements Power requirementsEquipment placement Auxiliary equipmentConnecting the unit Hardware SetupTo connect the AP800 Networking Units Installation ~ InstallationLink connections To create a G-Link network Device IDsTo set the device ID Mixer Mode Installation ~ Installation Device typesErrors To set mixer modeEC reference LCD Programming Installation ~ LCD ProgrammingSwitching from one main menu category to another Menu TreesAdjusting a value Installation ~ LCD ProgrammingLock Panel Select PresetSystem parameters Set PasscodeUnit ID PA Adaptive ModeDevice ID Gate ParametersFirst Mic Priority Last Mic ModeMaximum Number of Mics Gate RatioHold Time Decay RateTo determine ambient level RS-232Manual Ambient Baud RateSerial Overrun Errors Modem ModeClear Password TimeoutInput Parameters Inputs 1-8, Input GlobalChairman Mic High Pass FilterThree-Band EQ Adaptive AmbientInputs A, B, C, D Echo CancellerNLP Adjust AEC ReferenceOutputs 1-8, A-D Output ParametersRouting Parameters Subbus 1Routing Guidelines Echo Cancellation SetupInternal Subbus Master Unit EC Reference busSlave Unit Meter Parameters Default MeterInputs, Outputs, ERL, and Erle Technical Services Group ~ 1-800-283-5936 USA ~ AP-Ware software requirements Description64MB RAM Installing AP-Ware To install AP-WareTo increase volume Remote ControlVolume Control To decrease volumeTo mute an input MutingTo mute an output Appendix a Specifications FCC, CSA, CEAppendix B Warranty This warranty is void ifFCC Part 15 compliance Appendix C ComplianceAppendices ~ Appendix C Compliance Pin Number Definable Status Default Description Appendix D Connector PinoutsControl/Status a pinout +5VDC Pin Number User Definable* Status Default DescriptionControl/Status B pinout Control/Status Pinout NoteRS-232 COM DCE Port Pinout Appendix E AccessoriesAppendices ~ Appendix E Accessories Pin Number ControlAppendices ~ Appendix F Serial Commands Appendix F Serial CommandsCommand syntax Mref40Appendices ~ Appendix F Serial Commands Error Codes AP800 Serial CommandsCommand Function Amblvl AambAGC ExplanationChairo BaudDecay DfltmERL ErleFMP FlowFPP Examples GainGate ExampleHold GmodeGratio LFPLVL LMOMaster Device Mdmode MdmodeMEQ Device MEQ CH BandMline MHPMinit MmaxMref MpassMtrx Input Outputmix Mtrx 18Device Mute CH W MuteNLP Device NLP CHDevice NOM CH NOMOffa Device PAAPcmd ExampleDevice Pevnt Location Event Event List LFP, PRESET, MUTE, GAIN, AGC, EQ, GMODE, ChairoPevnt EventRefsel PresetTout Device UID UIDVER Device VERInputs = Gated Routing Matrix Setup~ Appendix G SWorksheets AppendicesSystemwide Parameters Auto Mix Parameters Appendices ~ Appendix G WorksheetsBus Glossary Glossary ~ A-DGlossary ~ E-S Glossary ~ T-Z Index Index ~ A-Z