Connecting the Speakers to the System General

ENGLISH

CONNECTING THE SPEAKERS TO THE SYSTEM – GENERAL

Use two-conductor 16 gauge or thicker speaker wires. Measure enough wire to reach from your receiver or amp to the speaker. Keep in mind the extra length needed for run- ning the wire around doors and windows. Leave yourself about 12" of extra slack to allow moving the speakers or receiver with- out having to disconnect the wires.

Note that one of the terminals on the rear of the speaker is marked red (+) and the other black (-). Make certain that you connect the wire from the red (+) terminal of your amplifi- er to the red (+) terminal on your speaker, and the wire from the black (-) terminal of the amplifier to the black (-) terminal on your speaker. Most wire has some indication (such as color coding, ribbing, or writing) on one of the two conductors to help maintain consisten- cy. If your CS1000p sounds “thin” with little bass, it is likely that one of the speaker wires in the front stage (Left, Center or Right) is connected backwards. Double check all con- nections.

Strip 1/2" of insulation from each of the two conductors on both ends to expose the bare wire. Twist the exposed wire of each conductor to form two un-frayed strands. Connect two conductors to the receiver or amp (refer to the owner’s manual supplied with your electronics for assistance with proper hookup). Connect the two conductors on the other end of the wire to the speaker terminals.

FIGURE 2.

USING 5-WAY BINDING POSTS

EL USO DE POSTES DE

CONEXIÓN DE CINCO

POSICIONES

UTILISATION DES BORNIERS “CINQ FAÇONS”

GEBRAUCH VON FÜNFER-

VERBINDUNGSBOLZEN

ESPAÑOL

PUNTOS GENERALES PARA CONECTAR LAS BOCINAS AL SISTEMA

Use cables para bocinas de dos conductores de calibre 16 o más grueso. Mida la longitud necesaria de cable para cubrir la distancia entre su receptor o amplificador y cada uno de las bocinas. No se olvide incluir el largo que se requiera para instalar el cable en torno de las puertas y ventanas. Deje por lo menos 12 pulgadas (30 cm) adicionales para que pueda mover las bocinas o el receptor sin tener que desconectar los cables.

Tome nota de que en la parte trasera de la bocina uno de los postes es rojo (+) y el otro es negro (-). Cerciórese de conectar el cable del poste rojo (+) de su amplificador al poste rojo (+) de su bocina y el poste negro (-) de su amplificador al poste negro (-) de su bocina. En la mayoría de los cables se encuentra alguna indicación (color, costillaje, o letras) en uno de los cables que facilita efectuar las conexiones correctamente. Si al sonido de sus bocinas le falta “cuerpo” y sale con pocos bajos y casi sin imagen de centro, es muy probable que algún cable esté conec- tado al revés. Verifique todas las conexiones.

Pele 1/2 pulgada del material aislante de los extremos de cada uno de los dos conductores para exponer el alambre. Tuerza el alambre expuesto de cada conductor hasta que que- den dos hilos no deshilachados. Conecte los dos conductores al receptor o amplificador (consulte el manual de usuario de su equipo electrónico para más información al respec- to). Conecte los conductores en el otro extremo del cable a los postes de la bocina.

	Loosen hex nut	Insert speaker wire
	Desenrosque parcialmente	through hole
	Desenrosque parcialmente
	la tuerca hexagonal	Inserte el alambre para la
	Desserrer l’écrou	bocina en el orificio
	Desserrer l’écrou	Insérer le fil du haut-parleur
	Sechskantmutter lösen	Insérer le fil du haut-parleur
	Sechskantmutter lösen	dans le trou
		dans le trou
		Lautsprecher-Draht durch
		das Loch schieben

CS1000P specifications

Polk Audio has long been a respected name in the audio industry, delivering quality sound systems that combine cutting-edge technology with user-friendly design. One standout product in their extensive lineup is the Polk Audio CS1000P, a high-performance speaker system that brings a rich and immersive audio experience to home entertainment setups.

The CS1000P is designed with a strong emphasis on accuracy and clarity, making it an ideal choice for both music enthusiasts and movie lovers. One of its main features is the advanced driver technology. The system includes a powerful 10-inch Dynamic Balance woofer that produces deep, resonant bass while eliminating unwanted distortion. This means that whether you're listening to your favorite albums or enjoying a cinematic experience, the low frequencies are handled with precision and power.

Moreover, the CS1000P is equipped with a patented PowerPort bass venting technology, which enhances the overall bass response by smoothing out the air flow. This results in a more unified sound that is not only louder but also more natural, allowing listeners to fully appreciate the subtleties in their music and film dialogue.

Another key characteristic of the CS1000P is its tall, slender design, which is both aesthetic and functional. The speaker is engineered to fit easily into various room layouts without compromising on performance. Polk Audio has also meticulously crafted the enclosure using high-quality MDF material to reduce vibrations and ensure that the sound remains pure and clean.

Connectivity is another aspect where the CS1000P excels, featuring versatile compatibility with a wide range of audio components. It is designed to work seamlessly with receivers and amplifiers, offering both wired and wireless setup options, thanks to its advanced Bluetooth capabilities. This makes it easy to stream music directly from smartphones, tablets, or computers, enhancing user convenience.

In summary, the Polk Audio CS1000P is a powerful speaker system that combines innovative technologies and premium materials to deliver an exceptional audio experience. With its dynamic driver setup, advanced PowerPort technology, elegant design, and versatile connectivity options, it stands out as a top choice for anyone looking to elevate their home audio experience. Whether for music or movies, the CS1000P delivers the clarity, depth, and richness that Polk Audio is renowned for.