Digi 90000797_A manual W e r s u p p l y, Input power jack, J3 Input power supply

Page 19

A B O U T T H E D E V E L O P M E N T B O A R D

. . .

Power supply. .

P o w e r s u p p l y

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The development board provides a 3.3VDC switching power supply. Either a bench power supply or an AC wall adapter supplies input power to the development board. The required input voltage range is 9–30VDC.

Input power jack, J3

Input power supply

The input power jack, J3, is a barrel connector that accepts 9-30 VDC. The power jack is labeled J3 on the development board. This figure schematically represents the power jack’s polarity:

Ground 9-30VDC +/- 5%

The output current of this regulator is limited to 2.4 amps and the Digi Connect Wi- Wave module draws no more than .750 amps. Using these values as a guideline, and using an 80% efficiency for the switching regulator, the input power supply should be rated to provide at least 3 watts of power.

Important: The development board can use USB power as the power source for the 3.3V regulator. This is accomplished by simply connecting the USB

www.digiembedded.com

21

Image 19
Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Documentation UpdatesG i i n f o r m a t i o n RelatedTo contact Digi International by Use Contact informationA t u r e s About the ModuleA t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connectorPin Type Wlan Mini Card Signal Digi Connect Wi- Wave module edge connector PinoutChannel Center frequency Frequency spread MHz MHz MHz B p e r i p h e r a l c o n t r o l l e r2 1 b / g m o d e s a n d c h a n n e l s Channel AllocationsL t a g e m o n i t o r R e s e t g e n e r a t o r L t a g e r e g u l a t o r sW e r A t ’ s o n t h e d e v e l o p m e n t b o a r d FeaturesDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 No connect or Jtagtdi Vcc3.3 Pin Type SignalD s Debug signal breakout header LEDsAlternative methods to trigger I t c h e s a n d r e s e t f u n c t i o n a l i t yW e r s u p p l y Input power jack, J3 Input power supplyA G B r e a k o u t H e a d e r , P 2 Header signal mapJtag breakout B p e r i p h e r a l i n t e r f a c e , J Signal Debug breakout Header signal mapB u g b r e a k o u t h e a d e r , P 2 L a n d R P S M a c o n n e c t o r s FL connectorsFL cables RP-SMA connectors For more information Necessary Conditions for Integration Using the AntennaConnect Wi-Wave antenna configurations Attributes T e n n a Specification s 2 d B i D i p o l eDimensions N e r a l i n f o r m a t i o nAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram Attribute Band T e n n a Specification s 5 d B i D i p o l eColor Freq MHz Peak dBi Angle o Avg dBi Radiation pattern H-Plane 2.0 and 5.0 GHzRadiation pattern E-plane 2.0 and 5.0 GHz C h a n i c a l d i m e n s i o n s V i r o n m e n t a l Specification sParameter Limits W e r r e q u i r e m e n t sE x p o s u r e s t a t e m e n t F e t y s t a t e m e n t sModule Dimensions Development Board dimensions C P a r t 1 5 C l a s s B Appendix BCertificationsModifications FCC Declaration of Conformity Standards International EMC StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008