Digi 90000797_A manual L a n d R P S M a c o n n e c t o r s, FL connectors, FL cables

Page 23

A B O U T T H E D E V E L O P M E N T B O A R D

. . .

U.FL and RP-SMA connectors. .

assert the W_DISABLE# signal to the module, place a jumper between either pins 18 and 20 or pins 19 and 20.

As an alternative, you can drive this pin with a low voltage TTL or CMOS driver. When asserted, W_DISABLE# lights the DISABLE LED, DS3.

U . F L a n d R P - S M A c o n n e c t o r s

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

U.FL connectors	The development board has two U.FL connectors that pair with two RP-SMA
	connectors. U.FL connector P1 pairs with RP-SMA connector J1;U.FL connector P2
	pairs with RP-SMA connector J2.
U.FL cables	The development kit includes two U.FL-to-U.FL cables that can be used to connect
	the module and development board. The number of cables used depends on
	whether one antenna is used to transmit and receive or two antennas are used
	(diversity receive).
	Single antenna configuration: Connect one end of the U.FL cable to connector P1
	on the development board and the other end of the cable to connector P1 on the
	Digi Connect Wi-Wave module.
	Dual antenna configuration: In addition to the connections outlined in the Single
	antenna configuration, connect one end of the second U.FL cable to connector P2

www.digiembedded.com

25

Image 23

Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Documentation UpdatesG i i n f o r m a t i o n RelatedTo contact Digi International by Use Contact informationA t u r e s About the ModuleA t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connectorPin Type Wlan Mini Card Signal Digi Connect Wi- Wave module edge connector PinoutChannel Center frequency Frequency spread MHz MHz MHz B p e r i p h e r a l c o n t r o l l e r2 1 b / g m o d e s a n d c h a n n e l s Channel AllocationsL t a g e m o n i t o r R e s e t g e n e r a t o r L t a g e r e g u l a t o r sW e r A t ’ s o n t h e d e v e l o p m e n t b o a r d FeaturesDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 No connect or Jtagtdi Vcc3.3 Pin Type SignalD s Debug signal breakout header LEDsAlternative methods to trigger I t c h e s a n d r e s e t f u n c t i o n a l i t yW e r s u p p l y Input power jack, J3 Input power supplyJtag breakout Header signal mapA G B r e a k o u t H e a d e r , P 2 B p e r i p h e r a l i n t e r f a c e , J B u g b r e a k o u t h e a d e r , P 2 Debug breakout Header signal mapSignal FL cables FL connectorsL a n d R P S M a c o n n e c t o r s RP-SMA connectors For more information Necessary Conditions for Integration Using the AntennaConnect Wi-Wave antenna configurations Attributes T e n n a Specification s 2 d B i D i p o l eDimensions N e r a l i n f o r m a t i o nAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram Attribute Band T e n n a Specification s 5 d B i D i p o l eColor Freq MHz Peak dBi Angle o Avg dBi Radiation pattern H-Plane 2.0 and 5.0 GHzRadiation pattern E-plane 2.0 and 5.0 GHz C h a n i c a l d i m e n s i o n s V i r o n m e n t a l Specification sParameter Limits W e r r e q u i r e m e n t sE x p o s u r e s t a t e m e n t F e t y s t a t e m e n t sModule Dimensions Development Board dimensions C P a r t 1 5 C l a s s B Appendix BCertificationsModifications FCC Declaration of Conformity Standards International EMC StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008